|
|
|
Who's Online
There currently are 5611 guests and
3 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
very poolite and healpful secure transaction thanks allot
;
- Very good scan quality, PERFECT!
- Sehr gute scan Qualitaet, empfehlenswert!
Wolfgang Sundhaus
 ;
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
AV32H20EUS AV28H20EUS AV28H20EUB
SPECIFIC SERVICE INSTRUCTIONS
DISASSEMBLY PROCEDURE
REMOVING THE REAR COVER
1. Unplug the power c ord. 2. Remove the 12 (28� models), 13 (32� model) screws marked A as s hown in the Fig. 1. 3. Withdraw the rear cover toward you.
REMOVING THE POWER & DEF PWB
" After removing the rear cover. " After removing the rear CHASSIS. 1. Remove the 3 screws marked G. 2. Remove the POWER & DEF PWB.
REMOVING THE CHASSIS
" After removing the rear cover. 1. Slightly raise the both sides of the c hassis by hand and remove the two claws under the both sides of the chassis from the front cabinet. 2. Withdraw the chass is backward. (If necess ary, take off the wire clamp, connectors etc.)
CHECKING THE PW BOARD
To check the back side of the PW Board. 1) Pull out the chassis . (Refer to REMOVING THE CHASSIS). 2) Erect the c hassis vertically so that you c an easily check the back side of the PW Board. [CAUTION] " When erec ting the chassis, be careful s o that there will be no contacting with other PW Board. " Before turning on power, make sure that the wire connector is properly connec ted. " When conducting a check with power supplied, be sure to c onfirm that the CRT EARTH WIRE (BRAIDED ASS�Y) is connected to the CRT SOCKET PW board.
REMOVING THE SPEAKER
" After removing the rear cover. 1. Remove the 2 screws marked B, and remove the speaker holder as s hown in Fig. 1. NOTE : When removing the screws marked B of the speaker remove the lower side screw first, and then remove the upper one. 2. Remove the 2 screws C attac hing the speak er. 3. Follow the s ame steps when removing the other hand speaker.
WIRE CLAMPING AND CABLE TYING
1. Be sure to clamp the wire. 2. Never remove the c able tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new c able tie.
REMOVING THE AV TERMINAL BOARD
" After removing the rear cover. 1. Remove the 3 screws marked D as shown in the Fig. 1. 2. Remove the 2 claws mark ed E under the CHASSIS as shown in Fig. 2. 3. Remove the AV TERMINAL BOARD slightly in the direction of arrow F as shown in Fig. 2.
AV SW PWB
AV TERMINAL BOARD
E
E
Fig. 2
6
No.51945
|
|
|
> |
|
