|
|
|
Who's Online
There currently are 5958 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It took about 24-hours after my payment before I was able to get to the download. Apparently, payment processing is not 100% automated. That is no big deal, just be aware of that going in.
After I got to it, it was in good shape, easy to read, etc. Not some cheap FAX copy looking thing.
Also, this site was the cheapest I found. Another Plus!
 ;
Good price, very legible manual, exactly what I needed -- but had to wait a day to actually get the download of the manual. Would have preferred to download it immediately after payment rather than waiting for someone to "process" my order. I was surprised that I had to wait that long.
;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
AV28T25EKS AV28T25EKB AV28T55EKS AV28T25EIS
Measuring instrument
Item Ad justment of HORIZONTAL CENTER
Test point
Ad justment part 4.H-CENT.
Description 13. Receive a c ircle pattern s ignal. 14. Select 4.H-CENT and set the initial s etting value. 15. Adjust H-CENT to make C=D. 16. Press the MENU key and memoriz e the s et value.
C
D
90%
90%
L
Ad justment of HORIZONTAL SIZ E
5.H-SIZ E
17. Receive a circle pattern signal. 18. Select 5.H-SIZE and set the initial setting value. 19. Adjust H-SIZE and make sure that the horizontal sc reen size of the picture size is in the bellow table. 20. Press the MENU key and memoriz e the s et value. * The numeric of the REGULAR and 14:9 ZOOM modes are shown the length of the 90% horizontal siz e position ( L ) as shown in the figure abov e. 21. Input a NTSC VIDEO signal (60Hz) from the EXT terminal, and make sure that the horizontal screen size of the each ASPECT mode is in the below table. 22. Press the MENU key and memoriz e the s et value.
ASPECT MODE H SIZ E
PANORAMIC PAL=95% NTSC=94%
14:9 ZOOM L=495mm
16:9 ZOOM 92% [ SCREEN SIZE ]
16:9 ZOOM SUB TITLE 92%
FULL 92%
REGULAR L=450mm
Ad justment of EW-PIN Straight
6.EW-PIN
23. Select 6.EW-PIN and s et the initial s etting value 24. Adjust EW-PIN and make the 2nd.vertic al lines at the left and right edges of the screen straight. Also make s ure that the 3rd vertical lines are straight. 25. Press the MENU key and memoriz e the s et value.
26
No. 51942
|
|
|
> |
|
