|
|
|
Who's Online
There currently are 5593 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent, fast delivery, excellent product. Good luck!
;
This manual is for the usa model only. But it is clear
, accurate and comprehensive, including board layouts and schematics.
I found it extremely useful for my mitsubishi dp-86da, but the same diagram would also work for the realistic lab5000 and hi fi 80. Thanks.
;
Great to have extra resources for Service Manuals, Now days you can really not trouble shoot efficiently without one , Wayne at IRIONS TV & ELECTRONICS REPAIR Clearwater , Fl. 33755 727-446-7955
 ;
For five bucks you can barely buy a hamburger. Or for the same five bucks you can buy a service manual. Much more useful. (and better for your health, depending on where you buy your hamburgers).
Yes, there are free manual sites out there, but if they don't have what you want, you have to pay.
And five bucks isn't much. Not for full specs, schematics and adjustment and parts replacement procedures.
My only criticism is that grayscale illustrations aren't well rendered, but I've seen worse.
Schematics and text are clear.
I'll be happy to purchase from here again.
Mike
[email protected]
;
Impressively thorough. Even the simple operators manual helped me "fix" one of the 2 CD players in the unit. This unit reads CD's from the top so they should be installed in the magazines "upside down" from typical CD players. The CD player service manual helped me unjam a stuck carriage because somebody transported the box laying down loaded with CD's. A little lens cleaning & the player now works well! Thanks for you help at a great price! Joe
AV-29RX
SPECIFIC SERVICE INSTRUCTIONS
DISASSEMBLY PROCEDURE
REMOVING THE REAR COVER
1. Disconnect the power plug from wall outlet. 2. As shown in the Fig.2, remove the 16 screws marked A . 3. Withdraw the rear cover toward you.
CHECKING THE PW BOARD
To check the PW Board from back side. 1. Pull out the chassis (refer to REMOVING THE CHASSIS). 2. Erect the chassis vertically so that you can easily check the back side of the PW Board.
REMOVING THE AV TERMINAL BOARD
" After removing the REAR COVER. 1. As shown in Fig.2, remove the 5 screws marked B . 2. Then remove the AV TERMINAL BOARD.
CAUTION
" When erecting the chassis, be careful so that there will be no contacting with other PW Board. " Before turning on power, make sure that the wire connector is properly connected. " When conducting a check with power supplied, be sure to confirm that the CRT EARTH WIRE (BRAIDED ASS� Y) is � connected to the CRT SOCKET PW board.
REMOVING THE CHASSIS
" After removing the REAR COVER and AV TERMINAL BOARD. 1. Slightly raise the both sides of the chassis by hand and remove the
2 claws under the both sides of the chassis from the front cabinet.
2. Withdraw the chassis backward. (If necessary, take off the wire clamp, connectors etc.)
WIRE CLAMPING AND CABLE TYING
1. Be sure to clamp the wire. 2. Never remove the cable tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new cable tie.
REMOVING THE SPEAKER BOX
" After removing the REAR COVER. 1. As shown in Fig. 2, removing the
2
screws marked
C,
then
remove the speaker box. 2. Follow the same steps when removing the other hand speaker box. NOTE : When removing the screws marked C of the speaker box, remove the lower side screw first, and then remove the upper one.
CONTROL BASE
REMOVING THE CONTROL BASE
" After removing the chassis. 1. As shown in Fig.1, while pushing down the claws marked remove the CONTROL BASE in the arrow direction E .
F
D ,
E
CLAW
CHASSIS
Fig. 1
6
No.51729
|
|
|
> |
|
