|
|
|
Who's Online
There currently are 5630 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
;
It is OK, this manual help me to repair my dynacord
 ;
Good manual. Even it is an old printed manual, it is well scanned and complete, with all drawings, schematics and parts list. Very good return for the cost.
AV-N29301 AV-N34301
SPECIFIC SERVICE INSTRUCTION
DISASSEMBLY PROCEDURE
REMOVE THE REAR COVER
" Unplug the power plug. 1. Remove the 12 screws marked A as shown in Fig.2. 2. Remove the rear cover toward you. * When reinstalling the rear cover, carefully push it inward after inserting the chassis into the rear cover groove.
REMOVING THE SPEAKER
" After removing the rear cover and chassis. 1. As shown in Fig.2, remove the 4 screws marked H . 2. Follow the same steps when removing the other hand speaker.
CHECKING THE MAIN PW BOARD
1. To check the backside of the MAIN PW Board. (1) Pull out the chassis. (Refer to REMOVING THE CHASSIS). (2) Erect the chassis vertically so that you can easily check the backside of the MAIN PW Board.
REMOVING THE CHASSIS
" After removing the rear cover. 1. Slightly raise the both sides of the chassis by hand and remove the
2
claws under the both sides of the chassis from the front
cabinet. 2. As shown in the Fig.2, withdraw the chassis backward along the rail in the arrow direction marked B . (If necessary, take off the wire clamp, connector�s etc.) * When conducting a check with power supplied, be sure to confirm that the CRT earth wire is connected to the CRT SOCKET PWB and the MAIN PWB.
[CAUTION] � When erecting the chassis, be careful so that there will be no contacting with other PWB. � Before turning on power, make sure that the CRT earth wire and other connectors are properly connected.
WIRE CLAMPING AND CABLE TYING
1. Be sure to clamp the wire. 2. Never remove the cable tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new cable tie.
REMOVING THE TERMINAL BOARD
" After removing the rear cover. 1. As shown in Fig.2, remove the 3 screws marked C . 2. As shown in Fig.1, after removing the claw marked D in the direction of arrow mark. 3. When you pull out the TERMINAL BOARD in the direction of arrow marked E as shown in Fig.1, it can be removed.
TERMINAL BOARD
E REMOVING THE FRONT CONTROL PW BOARD
" After removing the rear cover and chassis. PIP PWB 1. As shown in Fig.2, remove the 3 screws marked F . 2. Then remove the FRONT CONTROL PWB.
REMOVING THE FRONT AV IN PW BOARD
" After removing the rear cover and chassis. 1. As shown in Fig.2, remove the 2 screws marked G . 2. Then remove the FRONT AV IN PWB.
D
Fig. 1
6
No. 51738
|
|
|
> |
|
