There are currently no product reviews.
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
Received downlink in less then 8 hours, Item was in good copy condition, and told me how to program the clock timer. The price was very resonable, and the process was very automated and was GREAT to work with.
Fast service, document is OK. Thanks! Searched for it long time.
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! DziΔkujemy za!
It answered my question, which was how to load the paper. I did notice that the very end of the manual was not visible.
Using the Tuner
You can preset up to 30 FM stations and up to 15 AM (MW) stations.
â¢ Even if the system is unplugged or if the power failure occurs, the preset stations will be stored for about 24 hours. However, in case the preset stations are erased, you will need to preset the stations again.
â¢ Preset numbers may have been set to factory test frequencies prior to shipment. This is not a malfunction. You can preset the stations you want into memory by following one of the presetting methods below.
To Change the FM Reception Mode
When you are tuned into an FM stereo broadcast, the âST.â indicator lights up and you can hear stereo effects. If an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose stereo effect. FM AUTO mode is also useful to suppress static noise between stations. To enter Monaural mode while receiving an FM broadcast, press the FM/PLAY MODE button on the Remote Control until âFM MONOâ appears on the display. Then, the âMONOâ indicator lights up. Each time you press the FM/PLAY MODE button, the display alternates between âFM AUTOâ and âFM MONOâ.
FM / AM
FM = 30, AM = 15 When changing the Band
On the Remote Control
1 2 3
Select a band by pressing the FM/AM button.
Press the 5 or â button to tune in a station. Press the SET button.
Preset number â1â will blink for 5 seconds. Within 5 seconds, proceed to the next step. When the display returns to the one set in step 2 after 5 seconds, press the SET button again.
FM AUTO Ã FM MONO To restore the stereo effect, press the FM/PLAY MODE button on the Remote Control until âFM AUTOâ appears on the display. Then, the âMONOâ indicator goes out and the âST.â indicator will light up.
Press the Numeric Keys, or the 3 or 2 button within 5 seconds to select the preset number.
Beat Cut (AM (MW) Reception)
Switching the Beat Cut mode may reduce beat noise. Each time you press the FM/PLAY MODE button while receiving an AM (MW) broadcast, the Beat Cut mode changes as follows. BEAT CUT 1 = BEAT CUT 2 = BEAT CUT 3 = BEAT CUT 4 = (back to the beginning)
Press the SET button within 5 seconds.
âSTOREDâ appears and after 2 seconds, the display returns to the broadcast frequency display. Set to the position where beat noise is small. â¢ The best position will differ depending on the AM (MW) broadcast station being received.
Repeat above steps 1 to 5 for each station you want to store in memory with a preset number.
To change the preset stations, repeat the same steps as above.
â¢ In AM (MW) broadcast, reception sensitivity will be changed by turning the AM (MW) loop antenna. Turn the AM (MW) loop antenna for best reception.