There are currently no product reviews.
ThankΒ΄s for your help, I already recived these manual from you
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
When something abnormal occurs with the Monitor, this function informs you of the condition of the Monitor with self-diagnostic lamps, allowing for smooth service work.
Remote sensor 1 2 3 Power lamp Self-diagnostic lamps (1 to 3)
MENU INPUT POWER
If the trouble still persists, follow the procedure below:
Check which lamps are lighting or flashing.
On the Self-diagnostic Report Sheet (below), check the box next to âLightsâ or âFlashesâ of the corresponding lamp or lamps. â¢ Only one lamp may light or flash, or all three lamps may do so.
2 3 4
Switch off the POWER switch on the back of the Monitor. Unplug the power cord. Call your dealer and tell which lamps are lighting or flashing. (Copy and fax the Self-diagnostic Report Sheet below.)
â If the screen monitor turns off and self-diagnostic lamps light or flash
If the self-diagnostic lamps light or flash in red, check the following before consulting the dealer where you purchased the Monitor. â¢ If self-diagnostic lamp 1 (upper) flashes, lamp 2 (middle) lights, and lamp 3 (lower) flashes This may be caused by the dusty intakes on the rear. If this happens, switch off the main power by POWER switch (set to ââ¡ (off)â), unplug the AC power cord, then clean the intakes by referring to the instruction on page 2. â After cleaning, switch on the Monitorâs main power again. If self-diagnostic lamps do not go off, consult your dealer immediately.
Note: If you switch on the main power immediately after switching it off (or after recovering from a brief power interruption), the self-diagnostic lamps may light (or flash), and no image may appear on the screen. In this case, switch off the main power again, wait for about 10 seconds, then switch it on again. If no self-diagnostic lamps light or flash, you can operate and use the Monitor as usual.
Self-diagnostic Report Sheet
Store name where you purchased the Monitor
â If the screen monitor dims a little and âTEMP. OVERâ lights (or flashes)
If âTEMP. OVERâ lights or flashes at the right bottom of the screen, check the following before consulting the dealer where you purchased the Monitor. âTEMP. OVERâ appears to warn you of the internal heat buildup, which is usually caused by accumulated dust around the intakes or by improper installation. If the cause of the internal heat buildup is eliminated, this indication disappears and the screen recovers the brightness. â¢ If âTEMP. OVERâ flashes in yellow This may be caused by the dusty intakes on the rear. If this happens, switch off the main power by POWER switch (set to ââ¡ (off)â), unplug the AC power cord, then clean the intakes by referring to the instruction on page 2. â After cleaning, switch on the Monitorâs main power again. If âTEMP. OVERâ still flashes, this trouble may be caused by improper installation or improper location of the Monitor. In this case, consult your dealer immediately to solve this improper installation and to improve the circumstances around the Monitor. â¢ If âTEMP. OVERâ lights in red âTEMP. OVERâ will be shown for abut two minutes, the Monitor will shut off automatically, then the Selfdiagonal lamps light in red. If this happens, switch off the main power by POWER switch (set to ââ¡ (off)â), unplug the AC power cord, then consult your dealer immediately.
Model Name: Plasma Display Monitor GM-V42UG/GM-V42UB
The self-diagnostic lamps light or flash as listed on the following table. Please give me immediate advice or service if necessary.
NO. Lamp position 1 2 3 Upper Middle Lower
& Lights & Lights & Lights
& Flashes & Flashes & Flashes & Flashes
Your Name: Telephone No.: Address: