|
Who's Online
There currently are 6041 guests and 2 members online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Hello from Germany - thank you very much for the manual for my Sharp "Searcher" - the handling of your internet area is outstanding..Mike
;
I am very happy with the owner's manual. I bought a used Casio and was so relieved that I was able to get a hold of a owner's manual. It was very easy to download the manual and I had no problems with printing it. Thank you! Nancy Whalen
;
The purchased manual is an high-quality scan of the original JVC paper-based Owner´s Manual. I am very satisfied!
;
Very satisfied with received document, all is right, Thank You very much, it was a Pleasure to work with You.
;
great site, the most easy and fastest way to find the manual you need, no 5 star because the manual was only available in german, but I speak german as well so no problem for me.
Self-diagnostic Indication
When something abnormal occurs with the Monitor, this function informs you of the condition of the Monitor with self-diagnostic lamps, allowing for smooth service work.
Remote sensor 1 2 3 Power lamp Self-diagnostic lamps (1 to 3)
MENU INPUT POWER
If the trouble still persists, follow the procedure below:
1
Check which lamps are lighting or flashing.
On the Self-diagnostic Report Sheet (below), check the box next to �Lights� or �Flashes� of the corresponding lamp or lamps. � Only one lamp may light or flash, or all three lamps may do so.
2 3 4
Switch off the POWER switch on the back of the Monitor. Unplug the power cord. Call your dealer and tell which lamps are lighting or flashing. (Copy and fax the Self-diagnostic Report Sheet below.)
� If the screen monitor turns off and self-diagnostic lamps light or flash
If the self-diagnostic lamps light or flash in red, check the following before consulting the dealer where you purchased the Monitor. � If self-diagnostic lamp 1 (upper) flashes, lamp 2 (middle) lights, and lamp 3 (lower) flashes This may be caused by the dusty intakes on the rear. If this happens, switch off the main power by POWER switch (set to �� (off)�), unplug the AC power cord, then clean the intakes by referring to the instruction on page 2. � After cleaning, switch on the Monitor�s main power again. If self-diagnostic lamps do not go off, consult your dealer immediately.
Note: If you switch on the main power immediately after switching it off (or after recovering from a brief power interruption), the self-diagnostic lamps may light (or flash), and no image may appear on the screen. In this case, switch off the main power again, wait for about 10 seconds, then switch it on again. If no self-diagnostic lamps light or flash, you can operate and use the Monitor as usual.
Self-diagnostic Report Sheet
Store name where you purchased the Monitor
� If the screen monitor dims a little and �TEMP. OVER� lights (or flashes)
If �TEMP. OVER� lights or flashes at the right bottom of the screen, check the following before consulting the dealer where you purchased the Monitor. �TEMP. OVER� appears to warn you of the internal heat buildup, which is usually caused by accumulated dust around the intakes or by improper installation. If the cause of the internal heat buildup is eliminated, this indication disappears and the screen recovers the brightness. � If �TEMP. OVER� flashes in yellow This may be caused by the dusty intakes on the rear. If this happens, switch off the main power by POWER switch (set to �� (off)�), unplug the AC power cord, then clean the intakes by referring to the instruction on page 2. � After cleaning, switch on the Monitor�s main power again. If �TEMP. OVER� still flashes, this trouble may be caused by improper installation or improper location of the Monitor. In this case, consult your dealer immediately to solve this improper installation and to improve the circumstances around the Monitor. � If �TEMP. OVER� lights in red �TEMP. OVER� will be shown for abut two minutes, the Monitor will shut off automatically, then the Selfdiagonal lamps light in red. If this happens, switch off the main power by POWER switch (set to �� (off)�), unplug the AC power cord, then consult your dealer immediately.
To
Model Name: Plasma Display Monitor GM-V42UG/GM-V42UB
The self-diagnostic lamps light or flash as listed on the following table. Please give me immediate advice or service if necessary.
Self-diagnostic lamps
NO. Lamp position 1 2 3 Upper Middle Lower
Conditions
& Lights & Lights & Lights
& Flashes & Flashes & Flashes & Flashes
TEMP. OVER
Your Name: Telephone No.: Address:
39
|
|
|
> |
|