There are currently no product reviews.
perfect! you just sent to me the copy in Italian witout even my specification!!!! so you are really smart cooperative and efficient. To my opinion the best place all over to get a manual of electronics!!!!
Well Well Well!!!! Good manual perfect for my hobby!!! As Before you have done a very well done work!!!! Thank you
Super nice! Good to have a manual in digital format.
Great job supplying the manual.
Many of these products weerepretty obscure, so it was great that you had
the manual for it!
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
Audio Dubbing (GR-D93/73 only)
The audio track can be customized only when recorded in the 12-bit and SP modes. ( pg. 26)
â Use the provided remote control.
Insert Editing (GR-D93/73 only)
You can record a new scene into a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in and outpoints. The original audio remains unchanged.
â Use the provided remote control.
PAUSE START/ STOP REW INSERT STOP
â Before performing the following steps, make sure that âTIME CODEâ is set to âONâ. ( pg. 25, 28) â Insert Editing is not possible on a tape recorded in the LP mode or on a blank portion of a tape. â To perform Insert Editing while watching in the television, make connections. ( pg. 17)
1 Play back the tape, locate the Edit-Out point and
press PAUSE (9). Confirm the time code at this point. ( pg. 13)
2 Press REW (3) until the Edit-In point is located,
then press PAUSE (9).
1 Play back the tape to locate the point where editing
will start, then press PAUSE (9). While holding A. DUB (D) on the remote control, press PAUSE (9). The â9Dâ and âMICâ indicators appear. the microphone.
â To pause dubbing, press PAUSE (9).
3 Press and hold INSERT (I) on the remote control,
then press PAUSE (9). The â9Iâ indicator and the Time Code (min.:sec.) appear and the camcorder enters Insert-Pause mode.
3 Press PLAY (U), then begin ânarratingâ. Speak into 4 To end Audio Dubbing, press PAUSE (9), then STOP
4 Press START/STOP to begin editing.
â Confirm the insert at the time code you checked in step 1. â To pause editing, press START/STOP. Press it again to resume editing.
5 To end Insert Editing, press START/STOP, then
(8). To hear the dubbed sound during playback Set âNARRATIONâ to âONâ or âMIXâ. ( pg. 25, 28)
â Program AE with special effects (
pg. 30) can be used to spice up the scenes being edited during Insert Editing.
â Sound is not heard from the speaker during Audio Dubbing. â When editing onto a tape that was recorded at 12-bit, the old and new soundtracks are recorded separately. â If you dub onto a blank space on the tape, the sound may be disrupted. Make sure you only edit recorded areas. â If feedback or howling occurs during TV playback, move the camcorderâs microphone away from the TV, or turn down the TVâs volume. â If you change from 12-bit to 16-bit in mid-recording and then use the tape for Audio Dubbing, it is not effective from the point where 16-bit recording began. â During Audio Dubbing, when the tape moves to scenes recorded in the LP mode, scenes recorded in 16-bit audio or a blank portion, Audio Dubbing stops. â To perform Audio Dubbing while watching on the television, make connections. ( pg. 17) â To perform Audio Dubbing with a video unit connected to the camcorderâs AV connector, first set âS/AV INPUTâ to âONâ in VIDEO Menu. ( pg. 25, 28) The âAUXâ indication appears instead of âMICâ.
â During Insert Editing, the date and time information changes. â If you perform Insert Editing onto a blank space on the tape, the audio and video may be disrupted. Make sure you only edit recorded areas. â During Insert Editing, when the tape moves to scenes recorded in the LP mode or a blank portion, Insert Editing stops. ( pg. 43)
Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…