There are currently no product reviews.
Great service. Fast response. High quality scan. Good price.
Thank you very much!!!
Well-scanned, complete manual. Contains the information needed for repair and maintenance.
It's great to be able to obtain a precious technical information for a real old equipment. The one I got helps me a lot in the area of wiring diagram to repair my antique. PDF gave me clear enough information to find out thr details. Thanks for giving me the oppotunity to be able to access to almost vanished informations.
Another excellent aquisition. Fine detailed manual. Thanks
Good quality for the scan, complete, but as usual for Tascam, not so comprehensive !
SECTION 2 MECHANISM ADJUSTMENT
2.1 PRELIMINARY REMARKS ON ADJUSTMENT AND REPAIR 2.1.1 Precautions 1. When fastening parts, pay careful attention to the tightening torque of each screw. Unless otherwise specified, tighten a screw with the torque of 0.039 NÂ·m (0.4 kgfÂ·cm). 2. Be sure to disconnect the set from the power supply before fastening and soldering parts. 3. When disconnecting/connecting wires, be careful not to get them and their connectors damaged. (Refer to the Section 1.) 4. When replacing parts, be very careful neither to damage other parts nor to fit wrong parts by mistake. 2.1.2 Necessary jigs 1
Torque driver YTU94088
2.1.3 Notes on procedure for disassemby/assembly The disassembling procedure table (Table 2-2-2 on page 2-5, a part of the table is shown below for reference) shows the procedure to disassemble/reassemble mechanism parts. Carefully read the following explanation before starting actual disassembling/reassembling work. The item numbers (circled numbers) in the following explanation correspond to those appearing under respective columns of the table. (1) Circled numbers appearing in this column indicate the order to remove parts. When reassembling, follow these numbers in the reverse order. Circled numbers in this column correspond to those appearing in drawings of this section. (2) This column shows part names corresponding to circled numbers in the left column.
(3) The symbol (T or B) appearing in this column shows the side which the objective part is mounted on. T = the upper side, B = the lower side (4) Symbols appearing in this column indicate drawing numbers. (5) This column indicates parts and points such as screws, washers, springs, and others to be removed/fitted for disassembling/reassembling the mechanism. Besides such the parts, this column occasionally indicates working points. P= W= S= *= etc. Example Spring Washer Screw Lock (L), soldering (SD), shield, connector (CN),
Slit washer fitting jig YTU94121A
Chip IC replacement jig PTS40844-2
Guide driver YTU94148A
â¢ Remove (W1) = Washer W1. â¢ * Remove the solder at (SD1) = Point SD1. â¢ * Disconnect A = Connector A . (6) Numbers in this column represent the numbers of notes in the text. For example, â1â means âNote 1â. ( F o r p a r t s t h a t n e e d p h a s e a d j u s t m e n t a f t e r reassembling, refer to â2.2.7 Check and adjustment of mechanism phaseâ.) (7) This column indicates required after-disassembling/reassembling work such as phase adjustment or mechanism adjustment.
Part Name T T T T T 5
Fig. 1 2 2 2 3 5
Point 3(S1),(L1a)-(L1d) (W2) (W2) (S2b),2(S2a),(W2) (W3a) 5
Note 1a, 1b, 1c, 1d 2a, 2b 2a, 2b 2d 3b 5
A Cassette housing assembly
2a 2b 2c 3a
Reel disk (SUP) assembly Reel disk (TU) assembly Reel cover assembly Tension arm assembly 5