|
|
|
Who's Online
There currently are 5983 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Came in the mail within a few hours. Gave clear instruktion on maintaines. Is of great use to have this manual in house
 ;
Easy to access. Clear instructions. No problems. Printed fine.
;
Great scan but please note that it is entirely in GERMAN.
;
High quality scan of the manual, very quick and easy download and very important, a truly honest price. thanks
;
Minden rendben, de két megjegyzés, az ábrák nehezen kivehetők és a fizetés után 24 órát kell várni a letöltésre.
TROUBLESHOOTING EN
Although Snapshot is attempted, flash does not take place.
� The subject is too bright with the flash set to � ±0A� or �C ±0A�. HSet the flash mode to �ON�. ( pg. 29) � If blinks, the flash is being charged. HIt can take up to 10 seconds to charge the flash. � The camcorder is in the Record mode. HSet the camcorder in the Record-Standby mode. ( pg. 33, 35)
49
When the camcorder is connected via the DV connector, the camcorder does not operate.
� The DV cable was plugged/unplugged with power turned on. HTurn the camcorder�s power off and on again, then operate it.
Images on the LCD monitor appear dark or whitish.
� In places subject to low temperature, images become dark due to the characteristics of the LCD monitor. This is not a malfunction. HAdjust the brightness and angle of the LCD monitor. ( pg. 15, 17) � When the LCD monitor�s fluorescent light reaches the end of its service life, images on the LCD monitor become dark. HConsult your nearest JVC dealer.
Although a Snapshot is taken with the flash, RedEye Reduction does not take place.
� The subject does not look straight toward the flash. � The subject does not look at the first flash, which is an important part of Red-Eye Reduction. HThe subject should look straight toward the flash, especially the first flash. If the subject does not see the first flash, it will be difficult for Red-Eye Reduction to take place. ( pg. 33) � The camcorder is too far from the subject. HThe flash is effective for subjects at a distance of approx. 0.7 m (2 ft) to 2 m (6.5 ft) from the camcorder. ( pg. 33)
Colored bright spots appear all over the LCD monitor or the viewfinder.
� The LCD monitor and the viewfinder are made with highprecision technology. However, black spots or bright spots of light (red, green or blue) may appear constantly on the LCD monitor or the viewfinder. These spots are not recorded on the tape. This is not due to any defect of the unit. (Effective dots: more than 99.99 %)
Other problems
The POWER/CHARGE lamp on the camcorder does not light during charging.
� Charging is difficult in places subject to extremely high/low temperatures. HTo protect the battery, it is recommended to charge it in places with a temperature of 10°C to 35°C (50°F to 95°F). ( pg. 52) � The battery pack is not attached firmly. HDetach the battery pack once again and re-attach it firmly. ( pg. 12)
The cassette will not load properly.
� The battery�s charge is low. HInstall a fully charged battery. ( pg. 12)
The memory card cannot be removed from the camcorder.
HPush in the memory card a few more times. ( pg. 16) � The memory card lock switch is set to the lock position. HSlide the memory card switch to the unlock position. ( pg. 16)
�SET DATE/TIME!� appears.
� The built-in clock�s battery has run out. HConsult your nearest JVC dealer for replacement. � The previously set date/time is erased.
Picture does not appear on the LCD monitor.
� The viewfinder is pulled out and �PRIORITY� is set to �FINDER�. HPush the viewfinder back in or set �PRIORITY� to �LCD�. ( pg. 17, 29, 31) � The LCD monitor�s brightness setting is too dark. HAdjust the brightness of the LCD monitor. ( pg. 15) HIf the monitor is tilted upward 180 degrees, open the monitor fully. ( pg. 17)
Files stored in the memory card cannot be deleted.
� Files stored in the memory card are protected. HRemove protection from the files stored in the memory card and delete them. ( pg. 27)
When the image is printed from the printer, a black bar appears at the bottom of the screen.
� This is not a malfunction. HBy recording with �DIS� activated ( be avoided. pg. 29, 30) this can
An error indication (E01 � E04 or E06) appears.
� A malfunction of some kind has occured. In this case the H camcorder�s functions become unusable. pg. 51
The remote control does not work.
� �REMOTE� is set to �OFF�. HSet �REMOTE� to �ON�. ( pg. 29, 31) � The remote control does not point at the remote sensor. HPoint at the remote sensor. ( pg. 21) � The remote control batteries are exhausted. HReplace the batteries with fresh ones. ( pg. 21)
REFERENCES
|
|
|
> |
|
