There are currently no product reviews.
Manuale perfetto. Ottimo e utilissimo. Grazie a questo manuale ho potuto realmente risolvere il complesso problema della stampante.
Was very fast and accurate service. Just what I needed. I recommend to everyone.
Very good scan quality, only PC Board scan not enough contrast.
First of all I must say that I received the manual in just a few minutes after placing the order. The copy is well done ββand very readable. I will buy others soon... Thanks, Meyer
Good service manual. I gat all I want. Copy is good, but could be better. All clear and useful. I sincerely recommend.
2.13.3 Linearity adjustment The following flowchart shows the linearity check/adjustment procedure.
Connect an oscilloscope (CH: + Slope) and, while triggering it with the HID signal, observe the ENV OUT waveform.
PB switching point adjustment
The following flowchart shows the PB switching point adjustment procedure. Load the alignment tape.
Play the alignment tape, then set âATFâ (Auto Tracking Find) in âDeck Controllerâ of the SSS Software to ON. (Note 3)
The âPB Switching Pointâ in the Adjustment Utility of the SSS software is adjusted automatically.
Ensure that the ENV OUT waveform is linear and parallel, without a noticeable drop or variation in the overall level. If the waveform linearity is poor or there is a noticeable drop in level, adjust the guide roller by turning it with the roller driver.
2.13.5 Error rate adjustment The following flowchart shows the error rate adjustment procedure.
Record for about 5 minutes. (Note 6)
Set âATFâ (Auto Tracking Find) to OFF using âDeck Controllerâ of the SSS Software (Note 4). Observe the ENV OUT waveform to confirm that the overall waveform balance and linearity levels vary in accordance with the tracking variation as shown in Fig. 2-18-3. Repeat above steps as required. Is the PB ENV waveform ideally stable and does it vary ideally according to the tracking variation?
While playing the recorded signal, adjust âVCO Center Frequency (ME SP)â or âVCO Center Frequency (ME LP)â in âDeck Sectionâ of the Adjustment Utility. To adjust VCO Center Frequency (ME SP) : Set Viterbi OFF. To adjust VCO Center Frequency (ME LP) : Set Viterbi ON.
Yes The linearity adjustment is complete if the PB ENV waveform is ideally stable and varies ideally according to the tracking variation. To close, play a prerecorded tape and check the audio and video.
Is the obtained error rate minimum (almost the typical value)?
The error rate adjustment is complete when the minimum error rate which is no higher than the typical value is obtained. (Note 5)
Note 5 : â¢ The âtypical valueâ refers to the following: CH1 or CH2: < 498.; with Viterbi OFF. Inter-channel difference: < 10 times between CH1 and CH2. Note 6 : â¢ It is desirable to use a brand-new tape or an unused section of tape. This is to assure the adjustment reliability because using a damaged tape increases the error rate.
PB ENV waveform
Adjust variation in the parallelism
Fig. 2-18-4 PB ENV Waveform Note 3 : â¢ The VHS section has an A/C head, and the first tracking position can be locked using the CTL pulse and drum FF when AT is off. Therefore, the linearity of the VHS section can usually be adjusted with AT off. However, this adjustment method is not available with the DV section, which does not have the A/C head. If ATF is turned off, the DV section performs tracking only of the speed system. Therefore, as time passes, the servo will be lost and the linearity adjustment will become difficult. Note 4 : â¢ Since the speed servo function is active when ATF is off, there will be no problem even if the DVC ATF function is off, provided that it is for a few minutes.
Error rate measuring method
It is not necessary to use the error rate jig (YTU93083) or a frequency counter. The Service Support System Software displays the error rates of video CH1, CH2 and totals. When measuring the error rate of a channel, be sure to total the values of the video and the audio errors.