There are currently no product reviews.
Thanks so much for the Owner's manual for my Sony PS - FL1. I had purchased the turntable off of eBay. It came in and looked great. Packed well and appeared to be great. I balanced and aligned the tone are and hooked it up. When trying to play a record the tone are would move to the right place and just before it would drop to play it moved back off the edge of the record before touching down. I searched the net for an answer to this issue. No luck. Then I purchased the owners manual and sure enough there was a place to adjust where the stylus touched down. That adjustment solved the problem and saved me a $35 feet to have the player checked out. The manual is well written and easy to understand. It is a must have for anyone with this front loading Sony turntable.
Some years back I pruchased a Sansui G-9000. I had it cleaned up and a problem with the left channel repaired. When I got it back I hooked it up to my tape decks, turn tables, TV and it played great. The only thing I was not really satisfied with was the performance of my Graphic Equalizer. I purchased this owner's manual had poured myself a cup of coffee. The manual is well organized and written in plain language. It also contained the solution to my dissatisfaction. By using the preamp connections coupled I was able to run everything through my graphic equalizer and now enjoy the full potential of my complete system.
An excellent service for the price, however, it would also have been handy if the troubleshooter pages were included. The manual is only sent in the language of your country, thus it looks as though there are some pages missing. Otherwise highly recommended.
I am happy to get a rare TECHNICS SH-9090 Owner's Manual by PDF in clear copy.
Hr, klasse , good manual, verry fast on my e-mail, very usefull manual. rgds; ahm zeegers
3. Tape-to-tape editing is not possible.
â The source (another video recorder, camcorder) has not been properly connected. â All necessary power switches have not been turned on. â The input mode is not correct. â The camcorder has not been properly connected. â The input mode is not correct. Confirm that the source is properly connected. Confirm that all unitsâ power switches are turned on. Set the input mode to âAUâ. Confirm that the camcorder is properly connected. Set the input mode to âAUâ.
4. Camcorder recording is not possible.
1. Timer recording wonât work.
â The clock and/or the timer have been set incorrectly. â The timer is not engaged. â Timer recording is in progress.
Re-perform the clock and/or timer settings. Press TIMER and confirm that ââ°â is displayed on the display panel. Timer programming canât be performed while a timer recording is in progress. Wait until it finishes. Load a cassette with the Record Safety tab intact, or cover the hole using adhesive tape. Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the Record Safety tab intact. Check the programmed data and reprogram as necessary, then press TIMER again. The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme. Refer to "Guide Program Number Set" and re-perform the procedure ( pg. 10).
2. On-screen timer programming is not possible. 3. ââ°â and â]â on the display panel wonât stop blinking. 4. The cassette is automatically ejected, and ââ°â and â]â on the display panel wonât stop blinking. 5. ââ°â blinks for 10 seconds and the Timer mode is disengaged.
â The timer is engaged but thereâs no cassette loaded. â The loaded cassette has had its Record Safety tab removed.
â TIMER has been pressed when there are no programs in memory, or the timer record information has been programmed incorrectly. â The end of the tape was reached during timer recording.
6. The cassette is automatically ejected, the power shuts off and ââ°â and â]â wonât stop blinking. 7. SHOWVIEW does not timer-record properly.
â The recorderâs channel positions have been set incorrectly.
1. Whistling or howling is heard from the TV during camcorder recording. 2. When scanning channels, some of them are skipped over.
â The camcorderâs microphone is too close to the TV. â The TVâs volume is too high. â Those channels have been designated to be skipped.
Position the camcorder so its microphone is away from the TV. Turn the TVâs volume down. If you need the skipped channels, restore them ( pg. 38).
3. The channel cannot be changed.
â Recording is in progress.
Press PAUSE to pause the recording, change channels, then press PLAY to resume recording. Set the switch to the correct position. Perform manual setting again.
4. The remote control wonât operate the TV or satellite tuner. 5. Channel settings that were made manually seem to have changed or disappeared. 6. No channels are stored in the recorder's memory.
â The TV/SAT./VCR switch is in the wrong position. â After the manual settings were made, Auto Channel Set was performed. â The TV aerial cable was not connected to the recorder when Auto Set Up was performed.
Connect the TV aerial cable to the recorder properly and turn off the recorder power once, then turn the recorder power back on again. The recorder will try Auto Set Up again ( pg. 4).
Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…