There are currently no product reviews.
It is perfect, exactly what we needed. It's like the paper version but less clutter.
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
Immediate response with excellent service - highly reccommended
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
Your recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction. % Â£2
Before starting, make sure the recorder is in the Stop mode.
Press PUSH JOG or (â¢ or Â£) on the remote control. ââ¢ 1â or âÂ£ 1â is displayed on screen and search begins in the corresponding direction. ï¬
ACTIVATE INDEX SEARCH
â To access index codes 2 through 9, press PUSH JOG or repeatedly until the correct index number is displayed. Ex.: To locate the beginning of B from the current position, press PUSH JOG twice. To locate the beginning of D from the current position, press PUSH JOG once. Current position
â When the specified index code is located, playback begins automatically.
Simply by pressing a single button, the recorder power comes on, rewinds, and begins playback of the last timer-recorded programme. If you have several programmes recorded, you can easily access any of them.
Before starting, make sure that the recorder is off and that the Timer mode is disengaged.
ACTIVATE INSTANT REVIEW
Next Function Memory
You can set your recorder's power to go off automatically after the tape is fully rewound. Before starting, make sure the recorder is in the Stop mode. For Automatic Power Off After Tape Rewind . . . . . . press REW, then press within 2 seconds.
If you want the power to be turned off automatically when the counter reads â0:00:00â (instead of at the beginning of the tape), press C. MEMORY so that the âMâ mark appears before pressing REW.
Returns to the counter reading of â0:00:00â to conveniently find a specific place on the tape automatically. ï¬ % %
B â1 C 1 D 2 E 3 F
SET COUNTER MEMORY
Press C. RESET during playback at a point you wish to locate later. The counter reads â0:00:00â. Then press C. MEMORY, and âMâ appears in front of the counter digits.
ACTIVATE COUNTER MEMORY
When you wish to return to the designated point, press STOP and then REW or FF. â The tape rewinds or fast-forwards and stops at about 0:00:00 automatically. â To cancel Counter Memory, press C. MEMORY again.
Tape Position Indicator
The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of â5â in relation to â0â (beginning) or 0 + â+â (end) shows you where you are on the tape. âO.S.D.â ( pg. 9) must be set to âONâ, or the indicator will not appear. Beginning
Press REVIEW. The recorder power comes on and the recorder searches for the index code indicating the start of the last timer-recorded programme. Once itâs found, playback begins automatically. The front display panel tells you how many programmes have been recorded. If you have, for example, 3 programmes, âREVIEWâ and "3" appear and blink. To watch the first of the 3 programmes, press REVIEW three times. The recorder searches and begins playback automatically. You can access a programme as far as 9 index codes away from the current tape position.
Depending on the type of tape used, there may be times when the indication is not correct.
Instant ReView is not possible while the recorder is in the Timer mode.