There are currently no product reviews.
Good,readable manual. I found other manuals that were not readable when it came to part ID, but the one downloaded from owner-manual.com was better than expected. I will do buisness with owner-manual.com again.
Service Manual that I received was very helpful to me. Thank you.
The manual is well organized and is easy to read. The chapters are following normal way to proceed.
This scanned manual is well done in that most all the pages except for one is straight and clear- the way I would do them. One page was upside down but that happens. For the money that is charged on this site you get a pretty good deal. Now with complex repairs, I still prefer to us paper manuals which I have to buy at stereomanuals but the one I got here was much less than the $45 he was charging but this is a larger than normal manual for three different units. I am a picky manual user because I have used original manuals from Sony and Teac.
Very useful service manual, was exactly what i needed.Good quality,reasonable price.Thank you.
(4) Adjust the AUDIO OUT waveform and Control pulse waveform by turning the screws (1), (2) and (3) little by little until both waveforms reach maximum. The screw (1) and (3) are for adjustment of tilt and the screw (2) for azimuth.
Level drop at the guide roller (supply side) C D (2)
A/C head (3) Level drop at the guide roller (take-up side)
AUDIO OUT â¢ Proper waveform variation: Always flat
CTL. P â¢ Improper waveform variation: Higher
Fig. 2-3-2a 2.3.3 A/C head phase (X-value) Fig. 2-3-1c
(A1) (B) (C) (D) (E) (F) (G) (H)
Equipment Measuring point External trigger
â¢ Alignment tape(SP, stairstep, NTSC) [MHP] â¢ PB â¢ Oscilloscope â¢ TP106 (PB. FM) â¢ TP111 (D.FF) â¢ A/C head base [Mechanism assembly] â¢ Maximum V.PB FM waveform â¢ A/C head positioning tool [PTU94010]
(a) Guide roller
Adjustment part Specified value Adjustment tool
(b) Guide pole
Fig. 2-3-1d 2.3.2 Height and tilt of the A/C head Note: â¢ Set a temporary level of the height of the A/C head in advance to make the adjustment easier after the A/C head has been replaced. (See Fig.2-2-6c.)
Signal Mode Equipment Measuring point External trigger Adjustment part Specified value (A) (B) (C) (D1) (D2) (E) (F) (G)
â¢ Alignment tape(SP, stairstep, NTSC) [MHP] â¢ PB â¢ Oscilloscope â¢ AUDIO OUT terminal â¢ TP4001 (CTL. P) â¢ TP111 (D.FF) â¢ A/C head [Mechanism assembly] â¢ Maximum waveform
(1) Play back the alignment tape (A1). (2) Apply the external trigger signal to D.FF (E), to observe the V.PB FM waveform at the measuring point (D). (3) Set the VCR to the manual tracking mode. (4) Loosen the screws (4) and (5), then set the A/C head positioning tool to the innermost projected part of the A/ C head. (See Fig. 2-3-3a.) (5) Turn the A/C head positioning tool fully toward the capstan. Then turn it back gradually toward the drum and stop on the second peak point position of the V.PB FM waveform output level. Then tighten the screws (4) and (5). (6) Perform the tracking operation and make sure that the V.PB FM waveform is at its maximum. If it is not at maximum, loosen the screws (4) and (5), and turn the A/C head positioning tool to bring the A/C head to a position, around where the waveform reaches its maximum for the first time. Then tighten the screws (4) and (5).
(1) Play back the alignment tape (A). (2) Apply the external trigger signal to D.FF (E), to observe the AUDIO OUT waveform and Control pulse waveform at the measuring points (D1) and (D2) in the ALT mode. (3) Set the VCR to the manual tracking mode.
Complete owner's manual in digital format. The manual will be available for download as PDF file aft…