|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
High quality scan of the manual, very quick and easy download and very important, a truly honest price. thanks
;
Minden rendben, de két megjegyzés, az ábrák nehezen kivehetők és a fizetés után 24 órát kell várni a letöltésre.
;
Manual correct, and complete. Downloads cleanly. Format of manual was presumably difficult to PDF to A4, but works reasonably well.
;
This was a hard to find manual. When I did find it , some sites wanted way too much for the file.
Owner-manual .com had it for a really reasonable price. Not only that but it was sent very quickly and was a quality scanned document, unlike some others I purchased from a different site.
Good job guys!!
Larry
;
Fast and courteous service. Product delivered as described. Thank you.
25
Before performing the following steps: � Make sure the satellite receiver is connected to the recorder's AV2 IN connector. ( pg. 24) � Programme the timer on the satellite receiver. � Insert a cassette with the safety tab in place.
SP/LP
1 2
SET TAPE SPEED
Press SP/LP ( ) to set the tape speed.
ATTENTION
Press and hold REC LINK for about 2 seconds. The button lights up and the recorder turns off automatically.
ENGAGE AUTO SATELLITE PROG REC MODE
� To disengage the Auto Satellite Prog Rec mode, press REC LINK. The light goes off. � If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode.
� Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on. � If you have connected another appliance other than a satellite receiver to the AV2 IN connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on. � Auto Satellite Prog recording and timer-recording cannot be done at the same time.
NOTES:
� Auto Satellite Prog recording is not possible with the AV1 IN/OUT connector. � When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON". � After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function ( pg. 19). � For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver. � Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer. � The REC LINK button blinks while Auto Satellite Prog recording is in progress. � Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode. � If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 1 will apply to all the programmes for Auto Satellite Prog recording. � The B.E.S.T. system ( pg. 20) does not work while Auto Satellite Prog recording is in progress. � Just Clock ( pg. 43) does not work when the Auto Satellite Prog Rec mode is engaged. � Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme. � If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the REC LINK button blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording. � You can also record a programme from your cable system in the same way if the system has a timer and is connected to the recorder's AV2 IN connector.
REC LINK
|
|
|
> |
|