There are currently no product reviews.
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
good scans, all is clear. all pages in order. recommended
2.4 Service position This unit has been designed so that the Mechanism and Main board assemblies can be removed together from the chassis assembly. Before diagnosing or servicing the circuit boards, take out the major parts from the chassis assembly. 2.4.1 How to set the âService positionâ (1) Refer to the disassembly procedure and perform the disassembly of the major parts before removing the Mechanism assembly. (2) Remove the screws that fix the Mechanism assembly to the Chassis assembly. If any other screws are used to fix the boards, remove them also. (3) Remove the combined Mechanism and Main board assemblies. (4) If any other major parts are used, remove them also. (5) Connect the wires and connectors of the major parts that have been removed in steps (1) to (4). (Refer to Fig. 2-41a.) (6) Place the combined Mechanism, Main board and other board assemblies upside down. (7) Insert the power cord plug into the power outlet and then proceed with the diagnostics and servicing of the board assembly. Notes: â¢ Before inserting the power cord plug into the power outlet, make sure that none of the electrical parts are able to short-circuit between the workbench and the board assembly. â¢ For the disassembly procedure of the major parts and details of the precautions to be taken, see â2.2 Removing the major partsâ. â¢ If there are wire connections from the Main board and Mechanism assemblies to the other major parts, be sure to remove them (including wires connected to the major parts) first before performing step (2). â¢ When carrying out diagnosis and repair of the Main board assembly in the âService positionâ, be sure to ground both the Main board and Mechanism assemblies. If they are improperly grounded, there may be noise on the playback picture or FDP counter display may move even when the mechanism is kept in an inoperative status. â¢ In order to diagnose the playback or recording of the cassette tape, set the Mechanism assembly to the required mode before placing it upside down. If the mechanism mode is changed (including ejection) while it is in an upside down position the tape inside may be damaged. â¢ For some models, the mechanism and board assemblies are attached by connectors only. When carrying out a diagnosis or repair of the boards in the âService positionâ, make sure that the connectors are not disconnected. 2.5 Jig RCU mode This unit uses the following two modes for receiving remote control codes. (1) User RCU mode:Ordinary mode for use by the user. (2) Jig RCU mode: Mode for use in production and servicing. When using the Jig RCU, it is required to set the VCR to the Jig RCU mode (the mode in which codes from the Jig RCU can be received). As both of the above two modes are stored in the EEPROM, it is required to set the VCR back to the User RCU mode each time that an adjustment is made or to check that the necessary operations have been completed.These modes can be set by the operations described below. Note: â¢ Confirm the RCU mode when exchanged parts. Since some SERVICE PARTS sets the VCR to the Jig RCU mode as initial setting.
ONLY USED FOR HR-S5965EF CN1601 CN512
TP106 PB FM
Main board assembly
VR1601 R-Y VR1602 B-Y
S/P converter board assembly
SECAM board assembly
C3025 Timer clock TP GND TP7001 TEST
User RCU mode
Jig RCU mode
( not displayed)
Fig.2-5-1a User/Jig RCU mode 2.5.1 Setting the Jig RCU mode (1) Unplug the power cord plug from the power outlet. (2) Press and hold the âRECâ and âPAUSEâ buttons on the VCR simultaneously, while plugging the power cord plug into the power outlet. When the VCR is set to the Jig RCU mode, the symbols ( â : â ) in the time display of the FDP are turned off. (Refer to Fig.2-5-1a)