|
Who's Online
There currently are 319 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
 |
|
There are currently no product reviews.
 ;
ThankΒ΄s for your help, I already recived these manual from you
 ;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
 ;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
 ;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
57
4. Camcorder recording is not possible. â The camcorder has not been properly connected. â The input mode is not correct. Confirm that the camcorder is properly connected. Set the input mode to âL-1â,âL-2â, âF-1â or âS-1â.
TIMER RECORDING
SYMPTOM
1. Timer recording wonât work.
POSSIBLE CAUSE
â The clock and/or the timer have been set incorrectly. â The timer is not engaged. â Timer recording is in progress.
CORRECTIVE ACTION
Re-perform the clock and/or timer settings. Press â° and confirm that ââ°â is displayed on the display panel. Timer programming canât be performed while a timer recording is in progress. Wait until it finishes. Load a cassette with the Record Safety tab intact, or cover the hole using adhesive tape. Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the Record Safety tab intact. Check the programmed data and reprogramme as necessary, then press â° again. The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme. Refer to "Guide Program Number Set" and re-perform the procedure ( pg. 54).
2. Timer programming is not possible.
3. ââ°â and â]â on the display panel wonât stop blinking. 4. The cassette is automatically ejected, and ââ°â and â]â on the display panel wonât stop blinking. 5. ââ°â blinks for 10 seconds and the Timer mode is disengaged.
â The timer is engaged but thereâs no cassette loaded. â The loaded cassette has had its Record Safety tab removed.
â â° has been pressed when there are no programs in memory, or the timer record information has been programmed incorrectly. â The end of the tape was reached during timer recording.
6. The cassette is automatically ejected, the power shuts off and ââ°â and â]â wonât stop blinking. 7. VIDEO Plus+ does not timer-record properly.
â The recorderâs preset positions have been set incorrectly.
OTHER PROBLEMS
SYMPTOM
1. Whistling or howling is heard from the TV during camcorder recording. 2. When scanning channels, some of them are skipped over. 3. The preset cannot be changed.
POSSIBLE CAUSE
â The camcorderâs microphone is too close to the TV. â The TVâs volume is too high. â Those channels have been designated to be skipped. â Recording is in progress.
CORRECTIVE ACTION
Position the camcorder so its microphone is away from the TV. Turn the TVâs volume down. If you need the skipped channels, restore them ( pg. 48). Press PAUSE to pause the recording, change presets, then press PLAY to resume recording. Perform manual setting again.
4. Channel settings that were made manually seem to have changed or disappeared. 5. No channels are stored in the recorder's memory.
â After the manual settings were made, Auto Channel Set was performed. â The TV aerial cable was not connected to the recorder when Auto Set Up was performed.
Connect the TV aerial cable to the recorder properly and turn off the recorder power once, then turn the recorder power back on again. The recorder will try Auto Set Up again ( pg. 8). Re-set the remote control to the correct brand ( pg. 31, 32).
6. The remote control wonât operate the TV or satellite receiver.
â The remote control brand setting is incorrect.
|
|
 |
> |
|