JVC HR-V600AG
Owner's Manual

Timer Recording
Up to 8 timer recording programs can be made using G-CODE/ SHOWVIEW timer programing (for HR-V600AG only) or Express timer programing method as far as a year in advance. Remember, the clock must be set before you can program the timer.

E Return to normal screen

� Repeat steps 3 and 4 as necessary.

Press MENU on the remote control.

G-CODE�/SHOWVIEW� Timer Programing
(For HR-V600AG only)
The G-CODE numbers are the numbers next to the program in most TV listing. � Remember, the clock must be set before you can program the timer. � Be sure to read �G-CODE�/ SHOWVIEW� System Setup�. � Load a cassette with the record safety tab intact. The recorder turns on, and the counter is reset, automatically. � Select the appropriate colour system with �PAL/MESECAM� and �NTSC� in Function settings.

NOTES:

� If all the 8 programs have already been set, �PROGRAM FULL� appears on the TV screen. � After timer recording is completed, the recorder turns off automatically. � You can program the timer recording while a regular recording is in progress; the menu screens will not be recorded. � In case of a power failure after programming, the recorder�s memory backup keeps your selections (if the lithium battery is not exhausted). � If the tape reaches its end during recording, the recording stops and � � and � e� on the front display panel blink. Press 1 then 0 on the recorder to eject the cassette or press 3 on the remote control to rewind the tape.

G-CODE�/SHOWVIEW� System Setup
(For HR-V600AG only) INFORMATION
G-CODE and SHOWVIEW are different trademarks used to represent the same easy recording feature, but only the term G-CODE system will be used in the instructions. If you use the SHOWVIEW system, follow the same instructions listed for the G-CODE system. The G-CODE timer programming system eliminates the need to input channel, date, start and stop time data when setting the timer record function. Simply key in the G-CODE number for the TV programme you wish to record (found in most TV listings) and the recorder's timer is automatically programmed. You have to set �GUIDE PROG� numbers, which are assigned to each station for purposes of G-CODE timer programming, for all the stations stored in your recorder�s memory to get proper results. Before G-CODE setup you must have performed the procedures of Tuner Set and Clock Set.

A Press PROG on the remote control
to access the G-CODE/SHOWVIEW screen.
G-CODE/SHOWVIEW NO.

[0 � 9] [+/�] : EXPRESS PROGRAMING [PROG] : EXIT

B Press the appropriate Number keys to input the G-CODE
number, then press OK. Check to make sure the setting is accurate on the G-CODE Program screen.
G-CODE/SHOWVIEW NO. � P1 � NO. 12345678 STOP 22:00 SP [0 � 9] [ ] : DELETE [PROG] : EXIT DATE 25.04 : [OK] TV PROG 1

12345678

START 21:00

IMPORTANT
Perform the following procedure after Auto Set Up and/or the channel setting steps. After setting the Guide Program Numbers, channel positions may be incorrect if you stored or skipped channels. In this case, reperform Guide Program Number setting.

Guide Program Number Set A Access Main Menu screen, then Initial Set screen
Press MENU on the remote control. Press rt to place the pointer next to �INITIAL SET�, then press OK or e.

B Access G-CODE/SHOWVIEW Setup screen
Press rt to place the pointer next to �G-CODE/SHOWVIEW SETUP�, then press OK or e.

C Input Guide Prog number
Press rt or the Number keys to select the Guide Program number as shown in the TV listing, then press OK or e.

G-CODE/SHOWVIEW SETUP GUIDE PROG 2 TV PROG 5

[0�9] OR [ / ] : SELECT [MENU] : EXIT

C D

D Input receiving channel number
Press rt or the Number keys to select the number of the channel on which the

G-CODE/SHOWVIEW SETUP GUIDE PROG 2 TV PROG 5

� If the G-CODE/SHOWVIEW Setup G-CODE/SHOWVIEW SETUP screen appears after pressing OK, press the Number keys, PR+/� or GUIDE2PROG TV 5 PROG rt to input the number of the channel on which the broadcast for the G-CODE number is received on [0�9] OR [ / ] : SELECT [PROG] : EXIT the recorder, then press OK. � To set the tape speed, press SP/LP/EP (p). � To change the stop time, press STOP+/�. � To timer-record daily (Monday�Friday) or weekly serials, press DAILY (number key 8) or WEEKLY (number key 9). Pressing the button again makes the �DAILY� or �WEEKLY� display disappear. � If you made a mistake, press & to access the G-CODE/ SHOWVIEW screen again. � If an incorrect G-CODE/SHOWVIEW number or the one for a broadcast already finished has been input, �ERROR� is displayed for about 5 seconds, then the G-CODE/SHOWVIEW screen reappears. Press OK or PROG. � If �PROGRAM OVERLAPPED� appears, see �Program overlap warning display� ( 9). Press #. The recorder turns off automatically and �#� is displayed on the display panel.

Guide Program number�s broadcasts are received, then press OK or e. [0�9] OR [ / ] : SELECT � If the satellite broadcast is received on [MENU] : EXIT your recorder's auxiliary channel (�L-1� or �F-1�), select �L-1� or �F-1� for the channel position to which the satellite receiver is connected. �8�