|
|
|
Who's Online
There currently are 5975 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Good-quality scans. Detailed description. I hope I can repair the machine.
;
High-quality scanning. Detailed description. Recommend for all technician. A+++
;
This is a good quality scan of the original Service Manual from Nordmende, Germany. Contains the circuit diagram, PCB layout, adjust/tune instructions as well. It is NOT in English but in GERMAN language! That was quite right for my german friend from the lower east side in Berlin.
 ;
Received via e-mail this PDF manual is worth the money. This is a quality scan of a manual in excellent condition and is just as good as having the original manual in hand. I have later seen the original manual and it was printed in colour, but this particular manual is black & white but scan resolution is high end quality! All drawings and pictures are presented in great detail. So, nearly perfect score in my opinion.
If you own the turntable you also should own the manual!
;
I was very satisfied with the service manual I ordered and downloaded. I will definitely buy again from this seller.
KS-FX200
Mechanism Adjustment Section
Item 1.Head azimuth Adjusting & Confirmation Methods "Head Height Adjustment" Note Adjust the azimuth directly. When you adjust the height using a mirror tape, remove the cassette housing from the mechanism chassis. After installing the cassette housing, perform the azimuth adjustment. Adjust Std. Value
A Line
Head shield
1.load the mirror tape ( SCC-1659 ). Adjust with height The head is at low position adjustmentscrew (a) and azimuth adjustment screw (b) so during FWD. that line "A" of the mirror tape runs in the center between Lch and Rch in the reverse play mode. 2.After switching from REV to FWD then to REV, check that B Line the head position set in procedure "1" is not changed. *If the position has shifted, adjust again and check. 3.Adjust the azimuth screw (b) so that line "B" of the mirror tape runs in the center between Lch and Rch in the forward Head shield play mode. The head is at height position "Head Azimuth Adjustment" 1.Load the test tape ( VT724: 1kHz ) and play it back in the reverse play mode. set the Rch output level to maximum. 2.Load the test tape ( VT703: 10kHz ) and play it back in the forward play mode. Adjust the Rch and Lch output levels tomaximum, with azimuth adjustment screw (b). In this case, the phase difference should be within 45 . 3.Engage the reverse mode and adjust the output level to maximum, with azimuth adjustment screw (c). *The phase difference should be 45_Kor more. 4.When switching between forward and reverse modes, the difference between channels should be within 3dB. *Between FWD Lch and Rch, REV Lch and Rch. 5.When the test tape ( VT721 : 315Hz ) is played back, the level difference between channels should be within 1.5dB.
during REV.
Head azimuth screw Fixed screw
screw (c) screw (a) screw (b) 0 Phase 45
2.Tape Speed and Wow & Flutter
1.Check to see if the reading of the frequency counter & Wow Built-in Tape Speed flutter meter is within 2940-3090 Hz( FWD/REV ), and less volume resistor 2940-3090Hz than 0.35% ( JIS RMS ). Wow&Flutter 2.In case of out of specification, adjust the motor with a builtLess than in volume resistor. 0.35% (JIS RMS)
3.Playback Frequency response
1.Play the test tape ( VT724 : 1kHz ) back and set the volume position at 2V. 2.Play the test tape ( VT739 )back and confirm 0 + 3dB at1kHz/ 8kHz and -4+2dB at 1kHz/125Hz. 3.When 8kHz is out of specification, it will be necessary to read adjust the azimuth.
Speaker out 1kHz/8kHz : 0dB_}3dB, 125Hz/1kHz : -4dB+2dB,
1-15
 $4.99 KS-FX200 JVC
Parts Catalog Parts Catalog only. It's available in PDF format. Useful, if Your equipment is broken and You need t…
|
|
|
> |
|
