JVC KV-C1000J
Owner's Manual

KV-C1008
LVT1185-001A [A]

TV Tuner Unit : Instructions
0904MNMMDWJEIN EN

WARNINGS
� USE WITH DC 12 V NEGATIVE GROUND VEHICLES. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers. � DO NOT INSTALL THE MONITOR IN A LOCATION WHICH OBSTRUCTS DRIVING AND VISIBILITY, OR WHERE APPLICABLE LAWS AND REGULATIONS PROHIBIT THE INSTALLATION. � NEVER USE BOLTS OR NUTS FROM THE VEHICLE�S SAFETY DEVICES FOR INSTALLATION. If bolts or nuts from the steering wheel, brakes or other safety devices are used for installation, it may cause an accident.

© 2004 Victor Company of Japan, Limited

� Handle the Lithium coin battery (product number: CR2025) with care. � Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. � Do not recharge, short, disassemble, or heat the battery or dispose of it in a fire. These behaviors may cause the battery to be overheated, crack or fire. � Do not leave the battery with other metallic materials. Doing this may cause the battery to be overheated or cracked. It may cause a fire. � When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may be overheated, crack or fire. � INSTALL THE ANTENNA IN A PROPER LOCATION. � Do not poke the battery with tweezers or similar tools. Be sure to select a location for installation of the antenna so that the antenna is not protruding Doing this may cause the battery to be overheated or cracked. It may cause a fire. beyond the width or the front or back of the vehicle. If it is protruding, it might come into contact with a pedestrian or other object and cause an accident. Parts list � ATTACH THE WIRES CORRECTLY. The following parts are provided with this unit. After checking them, please set them correctly. If the wiring is not correctly performed, it may cause a fire or an accident. In particular, be sure to run and secure the lead wire so that it does not get tangled with a screw or the moving portion of a seat rail. Brackets Battery Remote controller AV bus cable Power cord To prevent short circuits, it is recommended that you disconnect the battery�s negative terminal and make all electrical connections before installing the unit. If you are not sure how to install this unit correctly, have it installed by a qualified technician. CR2025 � Avoid installing the unit in the following places. � Where it would hinder your safety driving. � Where it would be exposed to direct sunlight or heat directly from the heater or placed in an extremely hot place. Fixing screws � Where it would be subject to rain, water splashes or excessive humidity. � Where it would be subject to dust. � Where it would be positioned on an unstable place. � Where it could damage the car�s fittings. � Where proper ventilation would not be maintained, such as under a floor mat. � Where it would be located near inflammable objects (since heat is generated inside the unit).
�M4 x 8 mm RM-RK510 Remote sensor unit with double-faced adhesive tape

Diversity antennas with a cleaner

INSTALLATION
� The following illustrations show typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

Installing the antenna
Before installing: � The diversity antenna supplied with this unit is designed specifically for use with JVC TV tuner unit. (It cannot be connected to the car radio.) � Do not rub the antenna or the antenna�s cable with alcohol, benzine, thinner, gasoline or other volatile substances. � Attach to the inside of the car window glass. � Be sure to wipe the window surface where the antenna will be attached with the cleaner (supplied) to remove moisture, dirt, dust, wax, oil or other substances. (If there is moisture, oil or other wet substances on the attachment surface, the attachment tape will not stick well and easily come off.) � Identify the exact attachment location and confirm that the adhesive surfaces (antenna base and attachment parts) will not be placed on a heating wire, glass antenna or wiper motor. CAUTION Since there may be legal regulations defining the permissible installation locations for the monitor system which differ by country or by state, be sure to install the monitor in a location complying with any such laws.
Attachment parts

When used with KD-AV7008:
KD-AV7008 (separately purchased) Diversity antenna

TV tuner unit (in trunk)

1

When used with another monitor system:
Remote sensor unit Diversity antenna Monitor system (separately purchased) Antenna base

Peel off the cover paper from the antenna base and attach to the surface.

Peel off the cover paper.

Attachment location
Example of installation, side window
TV tuner unit (under the passenger�s seat)

2

Peel off the cover paper from the attachment parts in turn and attach to the surface.
Peel off the cover paper.

Installing the unit
While mounting the unit, be sure to use the tapping screws (not supplied) of appropriate length so that they will not damage any parts of the car.
Fixing screws �M4 x 8 mm

� When the attachment surface overlaps with an electrode

� When the attachment surface interferes with a rear wiper motor or a high-mounted brake light

Bracket Tapping screws (not supplied)

Attach the antenna to either the left or right of the electrode. Move the antenna�s attachment position upwards to avoid interference.
Electrode Heating wires

� Installing the antenna cord
Install the cord from the antenna to the TV tuner unit through the interior trim and under the carpet, and secure it using the cord clampers and mirror mats.
Cord clampers (separately purchased) Mirror mats (separately purchased)

Floor

TROUBLESHOOTING
� * � * � *

When used with any other monitor system than KD-AV7008. � * � * � * 1 The fuse blows. Are the red, yellow, and black leads connected correctly? Power cannot be turned on. Is the yellow lead connected? TV stations cannot be received. Is the area setting (see page 2) correct?

TV tuner does not work at all. Is the remote sensor unit connected correctly? No sound is heard. Have you adjusted the volume level on the monitor? Picture does not come on the screen. Is the correct input selected on the monitor?