There are currently no product reviews.
USING THE CD PLAYER (FOR AUDIO CD/MP3 CD)
PLAYING AN AUDIO CD/MP3 CD
Press 6 to play all the tracks in order starting with Track 1. The current track number and elapsed playing time appear on the display. AUDIO CD MP3 CD
To stop playing the video CD, press 7. To pause the picture, press 6. To cancel pause, press 6 again. To return to the menu page at any time, press RETURN. To select the desired track, press the number button. To select the previous/next track, press w/â. To search-play at high speed during playback, press 4/Â¢. Each time you press it, the playback speed changes. During search play, no sound comes out. Playing a Video CD without using PBC (PBC OFF): 1. Insert a video CD with PBC. The menu screen appears on the TV. 2. Press PBC to turn off PBC. After a while, the âPBCâ indicator goes out and the video CD is played sequentially from the first track. During playback, you can stop, pause, skip, or search-play in the same manner as for the audio CD. Playing a Video CD without PBC: You can play the video CD in the same manner as for the audio CD.
â¢ Make sure power cord is securely plugged into the AC power outlet (or that the batteries are fresh). â¢ Unplug the unit for a moment, and then plug it back in. â¢ Check the outlet by plugging in another device. â¢ Adjust volume setting. â¢ Make sure youâve selected the correct function: CD/VCD, TAPE, or RADIO. â¢ Adjust the FM/SW rod antenna for better FM/SW reception. â¢ Adjust the FINE TUNE knob for SW reception. â¢ Rotate the unit to achieve better MW reception. â¢ Try turning off electrical appliances near the unit, such as hair dryers, vacuum cleaners, or fluorescent lights. â¢ â¢ â¢ â¢ Make sure the tray contains a CD. Make sure the CDâs label is facing up. Make sure that Pause mode is not activated. Make sure CD function is selected. Maintenanceâ). CD sound skips â¢ Check CD for warping, scratches, or other damage. â¢ Check for vibration or shock that may affect the unit; move system if necessary. â¢ Inspect the recording head and clean it if necessary. â¢ Demagnetize recording head (as explained in âCare and Maintenanceâ). â¢ Audio/video cord is not connected to TV. â¢ Select the correct TV system. â¢ Replace the batteries.
System doesnât turn on.
To stop playing the CD, press STOP 7. To pause, press 6. The playing time blinks. To cancel pause, press 6 again.
Press RESUME. Then playback starts from the position where you have stopped. When a video CD with the PBC function is used with the PBC ON, the resume play does not work.
SELECTING A TRACK (AUDIO CD ONLY)
During playback, press 4/Â¢ on the unit or w/â on the remote control, to skip to the previous/next track or press the number button to specify the tack number. Then the selected track starts playing. â¢ You can also select a track in stop mode.
Poor radio reception
VARIOUS FUNCTIONS (USE REMOTE CONTROL)
OSD (On screen display): [VCD/Audio CD] You can view operational information on TV. Each time you press OSD, OSD function turns on and off. VIEW (Viewing up to 9 pictures): [VCD] Press VIEW. The picture page showing up to 9 tracks is displayed on the TV, and the first 20 seconds of each track is played sequentially. To view the previous/next picture page, press w/â. To normally play the track being briefly played, press 6. To normally play a desired track in the picture page, select the track number with the number button. SLOW (Playback speed reduction): [VCD] During playback, press SLOW. Each time you press it, playback speed changes to 1/2, 1/4, 1/8 and âPLAY (normal speed)â. During slow playback, no sound comes out. L/R (Channel selection): [VCD] Each time you press L/R, the channel output changes in the order of âMONO Leftâ, âMONO Rightâ and âSTEREOâ.
SEARCH PLAY (AUDIO CD ONLY)
During playback, press and hold 4/Â¢ to move backwards/forward through a track at high speed. You can quickly find a particular passage in the current track.
CD doesnât play
SELECTING AN ALBUM AND TRACK (MP3 ONLY)
When the TV is connected the disc imformation is displayed on the TV. While viewing this, you can select an album or a track. Selecting an Album (MP3 Only): 1. In stop mode or during playback, press ALBUM â/+ to select a desired album number. (e.g. âA02 (album number 2) T001â on the display) 2. Press 6 to start playback the track number 1 of selected album. Selecting a Track (MP3 Only): 1. After selecting the album, press TITLE â/+ to skip to the previous/next track in the current album. (e.g. âA02 T015 (track number 15 in the album number 2)â on the display) â¢ You can select a desired track with the number button. In this case, playback automatically starts. 2. Press 6 to start playback the selected track.
â¢ Clean the CD (as explained in âCare and
Distorted or noisy recordings
RESUME PLAY (AUDIO CD ONLY)
Press RESUME. Then playback starts from the position where you have stopped. GO TO (Starting playback from the designated time): [VCD/Audio CD] 1. Press GO TO. Then â--:-- (-- min. -- sec.)â appears on the display and on the TV. 2. Enter the time you want to start playback with the number button. Then playback automatically starts from that position. When a video CD with the PBC function is used with the PBC ON, this function dose not work. A-B REPEAT (Repeating section A-B): [VCD/Audio CD] You can repeatedly play a certain passage or scene by specifying the points A and B. 1. During playback, press A-B REPEAT at the start point you want to repeat. âA\â appears on the display. 2. Press A-B REPEAT at the end point. âA\Bâ appears on the display and the section A-B is repeatedly played. To exit A-B repeat playback, press A-B REPEAT once again. âA\Bâ disappears and normal playback takes place. A-B repeat playback also exits if the track selection operation is made. â¢ You may use A-B repeat playback over 2 or more tracks.
No video or video image distorted on TV Remote control does not work.
In stop mode, press RANDOM. The âRANDOMâ indicator lights on the display and playback starts in random order. Random play continues until you stop the CD. You can also enter the random play mode during playback. To exit the random play mode, press RANDOM once again or press 7. Note that the RANDOM operation is ignored in program play mode.
Amplifier : Output Power Speaker Impedance Phones 1 W x 2 (at 10 % THD) 8 ohm (8.5 cm x 2) 15 mW/ch output into 32 ohms Impedance 16 ohms - 1kohms 44.1 kHz 1 bit linear 100 Hz - 20 kHz 70 dB (min) 1.5 % (max) 40 dB (min) 50 dB (min) 20 (audio CD/VCD), 99 (MP3 CD)
During playback, press REPEAT. Each time you press it, the display changes as follows and each repeat play takes place. âREPEAT (for 1 track repeat)â \ âREPEAT GROUP (for all tracks in the current album: MP3 only)â \ âREPEAT ALL (for all tracks)â \ (back to the beginning) (On the TV, âREPEAT ALBâ is displayed instead of âREPEAT GROUPâ.) The repeat mode can be mixed with the other modes as follows: Mode Play Program REPEAT Current 1 track Current 1 track REPEAT ALL All tracks All programmed tracks REPEAT GROUP (MP3 only) All tracks in the current album â
Note: For the button operations of RESUME, PROGRAM, REPEAT and RANDOM, see âUSING THE CD PLAYER (FOR AUDIO CD/MP3 CD)â.
CARE AND MAINTENANCE
CLEANING THE EXTERIOR
â¢ Disconnect the system from AC power before cleaning the exterior of the unit with a soft dust cloth. Radio : Cassette :
Sampling Frequency D/A Converter Frequency Response Dynamic Range Harmonic Distortion Channel Separation Signal-to-Noise ratio Number of programmable tracks MPEG 1 VCD version 2.0 MPEG 1 layer 3 (MP3-CD) MPEG AUDIO MP3-CD bit rate 32 - 256 kbps Tuning Range Antenna Tape Speed Wow & Flutter Recording System Erase System S/N Track System Frequency Range (Normal) Power Supply Power Consumption Unit Dimension Mass
You can program the playing order of the tracks up to 20 for an audio CD/video CD and 99 for a MP3 CD. For Audio CD (and VCD): 1. In stop mode, press PROG. The âPROG.â indicator blinks on the display. 2. Select a desired track with w/â or number button, and then press PROG. again. âP01 (program number 1)â and âTxx (programmed track number)â appear. The âPROG.â indicator stays lit. 3. Repeat 1 and 2 to program other tracks , the number of programs increases. Then press 6 to start program play. To confirm the program, press 7 to return to stop mode and then press w/â. To clear the program, press 7 in stop mode. âCLr PrOGâ appears and the âPROG.â indicator goes out. Opening the CD door also clears the program. To skip to the track during playback, press w/â. â¢ When you program the VCD with PBC, be sure that âPBCâ indicator goes out on the display (PBC OFF). For MP3 CD: 1. In stop mode, press PROG. The âPROG.â indicator blinks on the display. 2. Select a desired album with ALBUM +/â. (e.g. âA02 T001â) 3. Select a desired track in the selected album with TITLE â/+ or number button. (e.g. âA02 T015â) 4. Press PROG. again. The âPROG.â indicator stays lit. 5. Repeat 1 to 4 to program other tracks, the number of programs increases. Then press 6 to start program play. How to confirm and clear the program is the same as for the audio CD.
â¢ Do not touch the signal surfaces. Hold by the edges, or by one edge and the hole. â¢ Do not affix labels or adhesive tape to the label surfaces. Also, do not scratch or damage the label. â¢ Discs rotate at high speed inside the player. Do not use damaged (cracked or warped) discs. General :
FM 88 MHz - 108 MHz, MW 530 kHz - 1600 kHz, SW 6 MHz-17 MHz FM/SW Rod Antenna, MW Ferrite Bar Antenna 4.75 cm/sec 0.35 % WTD AC Bias Magnetic Erase 35 dB (min) 4 track, 2 channel, stereo 125 Hz - 6300 Hz 110V-127V/220V-230V, 50 Hz/60 Hz DC 9 V, R20/D (13F) or equivalent size battery x 6 15 W (power on), 3W (Standby) 403(W) x 169(H) x 237(D) mm 3.3 kg (without batteries)
â¢ Dirty discs can cause poor sound quality. Always keep discs clean by wiping them gently with a soft cloth from the inner edge toward the outer perimeter. â¢ If a disc becomes dirty, wet a soft cloth in water, wring it out well, wipe the dirt away gently, and then remove any water drops with a dry cloth. â¢ Do not use record cleaning sprays or antistatic agents on discs. Also, never clean discs with benzene, thinner, or other volatile solvents which may cause damage to the disc surface.
VICTOR COMP ANY OF JAP LIMITED AN,
OTHER OPERATIONS FOR AUDIO CD/MP3 CD
Refer to âVARIOUS FUNCTIONSâ.
â¢ Donât expose cassette tapes to sunlight or store in hot places. High temperatures may warp the shell or damage the tape itself. â¢ Keep cassette tapes in their boxes when not in use. â¢ Cassette tapes can be erased by magnetic fields produced by magnets, electric motors, electrical transformers, and other devices. Keep tapes away from magnets and magnetic fields.
Printed in China 0902HMOCREORI
CLEANING THE TAPE HEADS
Iron oxide particles from the magnetic tape can build up on the parts that come in contact with the tape. These deposits can cause incomplete erasure, muffled playback sound, and might prevent automatic stop. To clean a cassette deck, open the compartment door, push the PLAY button and gently clean the heads, capstan, and pinch wheel with a head cleaner. Always unplug the power cord before cleaning, and allow 30 minutes drying time when using a liquid cleaner. Clean heads after every 25 hours of use. â¢ Demagnetize the head occasionally with a head demagnetizing cassette (available from many audio equipment stores). â¢ Never use any metal objects on or near the tape heads. â¢ Do not allow any cleaning material to fall into the tape assembly.
USING THE VCD PLAYER
Be sure that the system is connected to the TV.
PLAYING A VIDEO CD
Playing a Video CD with PBC (For VCD Version 2.0 Only): The system provides a PBC (Playback Control) function which utilizes a procedure (menu selection) programmed in the video CD. 1. Insert a video CD with PBC. The âPBCâ indicator lights on the display. The menu screen appears on the TV. 2. Press w/â to move through the previous/next menu page, and specify the item (track) in the menu with the number button. Then, the selected track is played. â¢ Once the video CD with PBC has stopped, the âPBCâ indicator goes out. (Pressing PBC replays the video CD.)