There are currently no product reviews.
Absolutely perfect! I've been trying to understand how to use all or at least some of the features of the receiver and especially the remote.
Copy of genuine owners/operators manual, very useful
The manual was a perfect match and was exactly what I was looking for. I'm very satisfied with my purchase.
Thank you for having the manual I needed for an older model Aiwa stero I had found on Ebay --- I wanted the Aiwa because I had tapes and cd's but I did not have a manual as to how to operate the system... I found what I needed and it has enabled me to set the system up for my enjoyment.
I wished detailed information of the JBL S310 and here I found it! Very happy with the service from this site!
Adjusting the Volume
You can adjust the volume level between MIN (0) and MAX (32) when the Unit is turned on. Turn the VOLUME control on the Unit to the right or left to increase or decrease the volume level. OR Press the VOLUME + or â button on the Remote Control to increase or decrease the volume level.
Showing the Time (CLOCK/ DISPLAY)
While listening to a CD or the radio, you can see the current time. To display the clock, press the CLOCK/DISPLAY button on the Unit. To return to the original display, press the same button until the original display appears. Note: You need to set the clock first in order for it to work. (See "Setting the Clock" on page 9.)
Adjusting the Brightness (DIMMER) [RD-T7GN Only]
CAUTION: DO NOT turn on the Unit and/or start playing any source without first setting the VOLUME control to MIN (0) , as a sudden blast of sound can damage your hearing. For private listening Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on headphones.
When operated on AC power ââââ
You can adjust the brightness of the display's backlighting. When the Unit is turned on: Each time you press the SNOOZE/DIMMER button on the Unit or on the Remote Control, the backlight fully turns on or dims. When the Unit is turned off(Standby): Each time you press the SNOOZE/DIMMER button on the Unit or on the Remote Control, the backlight dims or turns off. When the Sleep Timer is on: You can also dims or turn off the backlight with these buttons.
Reinforcing the Bass Sound (AHB PRO) [RD-T7GN Only]
You can reinforce the bass sound to maintain rich, full bass at low volume (you can use this effect only for playback): To get the effect, press the AHB (Active Hyper Bass) PRO button. The âBASSâ indicator lights up on the display. To cancel the effect, press the button again. The âBASSâ indicator goes out.
When operated on batteries ââââ
When the Unit is turned on, you can turn on the backlighting of the display for a few seconds. Each time you press the SNOOZE/DIMMER button on the Unit or on the Remote Control, the backlight turns on for a few seconds.
Power Batteries (6 pcs.): You can operate the System on batteries. When the batteries are exhausted, âNO BATTâ will appear on the display. In this case, replace with the new batteries. Memory Backup Batteries (3 pcs.): Your settings such as the preset stations, clock and timer are backed up with this batteries. CAUTION: If memory backup batteries are exhausted or not installed, and the AC power cord is disconnected or there is a power failure, the settings you have made will be erased from memory in approx. half a day.
Tone Control (BASS/TREBLE)
You can control the tone by changing the bass and treble.
I Press the BASS/TREBLE button until "BASS" 1.
or "TREBLE" appears on the display.
Each time you press the button, the display changes as follows: BASS = TREBLE = original display = (back to the beginning)
I Turn the Jog dial on the Unit or press the 2.
VOLUME +/â button on the Remote Control to adjust the level.
The bass or treble level changes between â6 and +6. (0: Flat)
To exit the tone control mode, press the BASS/TREBLE button until the original display appears, or wait for 15 seconds. To forcibly reset the bass and treble levels to 0 (FLAT), press the BASS/TREBLE button for 2 seconds or more.