|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
manual de usuario perfecto y completo de buena calidad de impresion y muy detallado ideal !
 ;
It`s full copy of a service manual from url http://www.philips.owner-manuals.com/PM3216-service-manual-PHILIPS.html
;
perfect! you just sent to me the copy in Italian witout even my specification!!!! so you are really smart cooperative and efficient. To my opinion the best place all over to get a manual of electronics!!!!
;
Well Well Well!!!! Good manual perfect for my hobby!!! As Before you have done a very well done work!!!! Thank you
;
Super nice! Good to have a manual in digital format.
Crossover Frequency Setting
Small speakers cannot reproduce the bass sound very well. So, if you have used a small speaker for any of the front, center, and rear channels, this receiver automatically reallocates the bass elements, originally assigned to the channel for which you have connected the small speaker, to another channel (for which you have connected the large speaker). If you have selected �LARGE� for all speakers (see page 12), this function will not take effect. To use this function properly, you need to set this crossover frequency level according to the size of the small speaker connected.
Low Frequency Effect Attenuator Setting
If the bass sound is distorted while playing back a source using Dolby Digital or DTS Digital Surround, follow the procedure below.
On the front panel ONLY:
1. Press SETTING repeatedly until �LFE ATT� (Low Frequency Effect Attenuator) appears on the display.
The display changes to show the current setting.
ST SETTING
On the front panel ONLY:
1. Press SETTING repeatedly until �CROSSOVER FRQ� (Crossover Frequency) appears on the display.
The display changes to show the current setting.
T SETTING
2. Press CONTROL UP 5/DOWN � to select the low frequency effect attenuator level.
� Each time you press the button, the display changes to show the following:
CONTROL DOWN UP
0dB
10dB
2. Press CONTROL UP 5/DOWN � to select the crossover frequency level according to the size of the small speaker connected.
� Each time you press the button, the display changes to show the following:
CONTROL DOWN UP
0dB: 10dB:
Normally select this. Select this when the bass sound is distorted.
Note:
This function takes effect only when the subwoofer (LFE) signals come in, (with �SUBWOOFER� set to �YES.�)
80HZ
100HZ
120HZ
Dynamic Range Compression Setting
You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when enjoying surround sound at night. � This function takes effect only when playing back a source using Dolby Digital.
� Use the following comments as reference when adjusting. 80HZ: 100HZ: 120HZ: Select this when the cone speaker unit built in the speaker is about 4 3 /4 inches (12 cm). Select this when the cone speaker unit built in the speaker is about 3 15 /16 inches (10 cm). Select this when the cone speaker unit built in the speaker is about 3 3 /16 inches (8 cm).
On the front panel ONLY:
Note:
Crossover frequency is not valid for the HEADPHONE mode.
1. Press SETTING repeatedly until �D_RANGE COMP� (Dynamic Range Compression) appears on the display.
T SETTING
The display changes to show the current setting.
CONTROL DOWN UP
2. Press CONTROL UP 5/DOWN � to select the appropriate item about the compression level.
� Each time you press the button, the display changes to show the following:
OFF
MID
MAX
OFF: MID: MAX:
Select this when you want to enjoy surround with its full dynamic range. (No effect applied.) Select this when you want to reduce the dynamic range a little. (Factory setting.) Select this when you want to apply the compression effect fully. (Useful at night.)
Note:
Dynamic Range Compression is not valid for the DTS Digital Surround.
13
|
|
|
> |
|
