|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
;
The owners manual for the Pioneer VSX-D603S was exactly what I needed. I received it in a timely manor and it was priced fairly. I definately will use your servise again. Thank You
;
This is a great manual. It was easy to read and very accurate. The size of the manual is small so email is no problem. I highly recommend it. The manual is very hard to find other than this website.
;
Manual was complete and available promptly, since I had lost my original manual. Very good response.
;
Whilst this is a photo copy, and some of the pages are a little askew, it was all readable and intact. A real bonus finding an old manual for a classic piece of kit that no other site had.
Great stuff.
Adjusting the equalization patterns� DIGITAL EQ 63Hz/250Hz/1kHz/4kHz/16kHz
You can adjust equalization patterns in five frequency bands (center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the front speakers. � Once you have made an adjustment, it is memorized for each source. Adjustable range: �8 (dB) to +8 (dB) (in 2 dB intervals) Initial setting: 0 (dB) for all bands � When adjustment is made, the DIGITAL EQ indicator lights up on the display. If no adjustment is required, set all the frequency bands to �0 (dB).� � The DIGITAL EQ indicator goes off from the display.
7 Attenuating the input signal�INPUT ATT
When the input level of analogue source is too high, the sound will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion. � Once you have made an adjustment, it is memorized for each source. � You cannot adjust this item directly from the remote control. INPUT ATT: ON Select to attenuate the input signal level. The INPUT ATT indicator lights up on the display. INPUT ATT: NORMAL Select to deactivate attenuation.
Initial setting: INPUT ATT: NORMAL
From the remote control:
Before you start, remember... There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
Adjusting the sound parameters for the Surround/DSP modes
You can adjust the Surround/DSP sound parameters to your preference. � For details about the Surround/DSP modes, see pages 46 to 48.
1 2
Press D. EQ FREQ repeatedly to select the band you want to adjust. Press D. EQ LEVEL + or � to adjust the equalization pattern of the selected band.
1 4 7 10
2 5 8 0
3 6 9 10
7 Adjusting the effect level for DSP modes �EFFECT
This setting is available only when one of the DSP modes (except ALL CH STEREO) is in use. To activate DSP mode, see page 50. � Once you have made an adjustment, it is memorized for each DSP mode. Adjustable range: 1 to 5 (in 1 step intervals) Initial setting: EFFECT: 3 As the number increases, the effect becomes stronger. Normally, select �3.�
1 2
3
Repeat steps 1 and 2 to adjust other bands.
Adjusting the bass sounds
7 Reinforcing the bass�BASS BOOST
You can boost the bass level�Bass Boost. � Once you have made an adjustment, it is memorized for each source. � You cannot adjust this item directly from the remote control. BASS BOOST: ON Select to boost the bass level. The B.BOOST indicator lights up on the display. Select to deactivate the Bass Boost.
From the remote control:
Press EFFECT repeatedly to select the level you want to adjust.
1 4 7 10 2 5 8 0 3 6 9 10
BASS BOOST: OFF
Initial setting: BASS BOOST: OFF NOTE This function affects only the sound coming out through the front speakers.
7 Adjusting the virtual room size for DSP modes �ROOM SIZE
This setting is available only when one of the DSP modes (except ALL CH STEREO) is in use. To activate DSP mode, see page 50. � If �SURROUND SPK� is set to �NO� (see page 28), this item is not adjustable. � Once you have made an adjustment, it is memorized for each DSP mode. � You cannot adjust this item directly from the remote control. Adjustable range: 1 to 5 (in 1 step intervals) Initial setting: ROOM SIZE: 3 As the number increases, the interval between reflections increases so that you will feel as if you were in a larger room. Normally, select �3.�
38
|
|
|
> |
|