There are currently no product reviews.
Although printing quality is not the best, the manual was very helpful in order to reactivate this ancient but still good electronic musical instrument.
as a first-time user and buyer from this site, i found the overall service outstanding!! this product is a godsend as, without it, i would never have been able to find my way around and use my machine as intended. i will certainly use this site again as required. many many thanx!!
This manual is exactly what I needed. This site always has every manual I need, and it is also much less expensive then most other sites. This is the only manual site I will use.
Useful manual, good scan, worth the pay if you find the unit difficult to operate.
Exactly as described, the full user-manual (145 pages). Perfect.
SPEAKER SYSTEM æ¬å£°å¨ç³»ç»
Thank you for purchasing JVC speakers. Before you begin using them, please read the instructions carefully to be sure you get the best possible performance. If you have any questions, consult your JVC dealer. æè°¢æ¨æ è´ JVC æ¬å£°å¨ã å¨å¼å§ä½¿ç¨ä¹åï¼è¯·æ¨ä»ç»é
è¯»æ¬ä½¿ç¨è¯´æä¹¦ï¼ä»¥ç¡®ä¿æ¨è·å¾æ¬å£°å¨ çæä½³æ§è½ãå¦æçé®ï¼è¯·ä¸ JVC ä»£çéå®åèç³»ã
Black é»è² Press æ
1. Remove the ending part of the vinyl covering from the cut. 2. Twist the wires.
1. ä»æå¼å¤å°å°¾é¨çå¡æå¥åä¸æ¥ã 2. æ§ç´§è¯çº¿ã
â¢ Connect the LEFT speaker terminals of the amplifier to the LEFT terminals of the speaker and RIGHT to RIGHT using the attached speaker cords as shown in the figure making sure polarity is correct; (+) to (+) and (â) to (â). Connect the black speaker wire to the (â) terminal. â¢ Turn off power to the whole system before connecting the speakers to the amplifier. â¢ The nominal impedance of the SP-MXS6MD is 6 â¦. Select for use an amplifier to which a speaker system with the load impedance of 6 â¦ can be connected. â¢ The maximum power handling capacity of the SP-MXS6MD is 50 W. Excessive input will result in abnormal noise and possible damage. In cases where the signals described below are applied to the speakers, even if the signals are below the maximum allowable input, they may cause an overload and burn the wiring of the speakers. Be sure to lower the amplifier volume beforehand. 1) Noise during FM tuning. 2) High level signals containing high frequency components produced by a tape deck in the fast forward mode. 3) Click noise produced when turning power of other components on and off. 4) Click noise produced when connecting or disconnecting cords with the power on. 5) Click noise produced when the cartridge is replaced with the power on. 6) Click noise produced when operating amplifier switches. 7) Continuous high frequency oscillation or high pitch electronically produced musical instrument sound. 8) Howling when using a microphones.
â¢ å¦å¾æç¤ºï¼ç¨éå¸¦çæ¬å£°å¨å¯¼çº¿å°æ¾å¤§å¨ä¸ç LEFTï¼å·¦ï¼æ¬å£° å¨ç«¯åæ¥å°æ¬å£°å¨çå·¦ç«¯åä¸ï¼æ¾å¤§å¨ç RIGHTï¼å³ï¼æ¬å£°å¨ ç«¯åæ¥å°æ¬å£°å¨çå³ç«¯åä¸ï¼å¹¶ç¡®è®¤ï¼ï¼ï¼ææ¯å¦æ£ç¡®å°æ¥å° ï¼ï¼ï¼æï¼ï¼ï¼ï¼æ¯å¦æ¥å°ï¼ï¼ï¼ãé»è²çæ¬å£°å¨å¯¼çº¿è¦æ¥å° ï¼ï¼ï¼ç«¯åã â¢ è¦å°æ¬å£°å¨è¿æ¥å°æ¾å¤§å¨æ¶ï¼é¡»å
ç½®ç³»ç»ççµæºã â¢ SP-MXS6MD çé¢å®é»æä¸º 6 â¦ï¼æ¬§å§ï¼ãéæ©ä½¿ç¨å¯è¿æ¥è´ è½½é»æä¸º 6 â¦ï¼æ¬§å§ï¼çæ¬å£°å¨ç³»ç»çæ¾å¤§å¨ã â¢ SP-MXS6MD çæå¤§åçä¸º 50Wï¼ç¦ï¼ãè¿å¤§çè¾å
¥ï¼å°é æ å¼å¸¸åªå£°ï¼çè³æåæ¬å£°å¨ãå½ä¸åçä¿¡å·è¾å
¥ï¼ä»å¯è½é æè¿è½½èç§æ¯æ¬å£°å¨å¯¼çº¿ï¼ æ
¨ã 1) å¨ä½ FM è°è°ä¸åççåªå£°ã 2) ç£å¸¦å½é³æºçå¿«ç»æ¨¡å¼ä¸äº§ççå«æé«é¢é¨åçé«çµå¹³ä¿¡å·ã 3) å¼å
¶ä»ç»ä»¶çµæºæ¶äº§ççåååªå£°ã 4) æ¥éççµæºçç»ä»¶é´çæ¥çº¿ææå¸æ¥çº¿æ¶äº§ççåååªå£°ã 5) æ¥éççµæºæ´æ¢å¡çæ¶äº§ççåååªå£°ã 6) æä½æ¾å¤§å¨å¼å
³æ¶äº§ççåååªå£°ã 7) è¿ç»çé«é¢çæ¯è¡æé«é³è°çµåè£
ç½®äº§ççä¹å¨å£°ã 8) ä½¿ç¨éº¦å
LVT0575-002A [UB, US, UF]