There are currently no product reviews.
Perfect for my use.Could have better pictures,but otherwise perfect ;)
This is one of four manuals I have downloaded recently.
Purchase was very straight forward and the authorising email arrived in about 4 hours.
The quality of the scan is good. Print is clear and square to the page edges.
Exactly as advertized. High quality digital copy of the Nak 610 user manual. Easy download and access. Highly recommended.
The manual was exactly what I wanted and I found it nowhere else. Thanks!
Having purchased a 1994 Kenwood music system from a Charity shop in 2013 (it was a high end product in its day), I found myself not quite knowing where to plug in what, and how to do this, that and the next thing. I needed a Manual, and after failure with another online 'Manual provider' I found Owner Manuals dot com. Well, I wasn't sure, but it was only $5, and if things didn't work out, I wouldn't have lost much...
But things DID work out. After paying my childrens inheritance money, $4.99, I was sent a Manual for my Kenwood System very quickly. Alas, it was in German, and being Scottish, I could not read it or get my system in order from it...a rapid email to them brought the English Manual in short order, and my retro-system was and IS up and running in it's regulation settings.
I am very grateful to http://www.owner-manuals.com for their quick service and for even having such an obsolete Manual in the first place! If you need a Manual for ANYTHING, try here first. I wouldn't be surprised if I bought a 1928 Marconi radio, and got the user Manual for THAT here too!
Activating Dynamic Range Compression
You can enjoy a powerful sound even at a low volume level by compressing the dynamic range (difference between the maximum and minimum sounds). â¢ This function takes effect only when Dolby Digital is activated. From the remote control ONLY: Press D.R.C. D.R.C â¢ Each time you press the button, the dynamic range compression mode alternates between on and off. Select âDRC ONâ while watching the DVD at night. (You can obtain a powerful sound at a low volume.)
To adjust the output balance for the front speakers and the rear speakers 1) Press SOUND repeatedly until one of the following adjustment indications appears on the display.
â¢ Each time you press the button, the adjustment indication on the display changes as follows:
00 F 00
00 R 00 SW
Normal indication (canceled)
00 F (Front) 00 : To adjust the output balance for the front speakers. 00 R (Rear) 00 : To adjust the output balance for the rear speakers. â¢ When selecting â3 STEREO,â you cannot adjust the output balance for the rear speakers. â¢ â00 F 00â and â00 R 00â are the initial settings (the output balances are at the center position). If you have already changed the setting, another value will appear.
Adjusting Dolby Surround
You can adjust the following settings while activating Dolby Surround. It is recommended that you make adjustments from your actual listening point while listening to reproduced sounds. â Output balance for the front speakers â Output balance for the rear speakers â Output level for the center speaker* â Output level for the rear speakers* â Output level for the subwoofer* â¢ When Dolby 3 Stereo is activated, you cannot adjust the rear speakers. * The adjustment is separately memorized for Digital Multichannel Surround (Dolby Digital and DTS Digital Surround), and for Dolby Pro Logic. â¢ Dolby Surround cannot be used with DSP modes. Once one of Dolby Surround is activated, DSP modes in use will be canceled. Before you start, remember... â¢ There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 3 again.
2) Press 3 or 2 to adjust the output balance.
3 : Decreases the left speaker output, or restores the right speaker output. 2 : Decreases the right speaker output, or restores the left speaker output.
â¢ Each output balance changes from OFF (silence), â06 (most reduction) to 00 (no reduction).
3) Repeat 1) and 2) for setting the other speakers.
1 2 3
Press AUX to select the external component as the source. Start playing a source encoded with Dolby Surround. Press PRO LOGIC repeatedly on the remote control to select Dolby Pro Logic or Dolby 3 Stereo.
The PRO LOGIC indicator lights up on the display. â¢ Each time you press the button, the indication changes as follows:
PRO LOGIC STEREO (canceled)
Now, you are ready to start adjustments. â¢ To adjust the output balance for the front speakers and the rear speakers, go to the next step. â¢ To adjust the output level for the center speaker, the rear speakers, and the subwoofer, go to step 5 on the next page.
TO BE CONTINUED ON THE NEXT PAGE