|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
;
excellent value & price! Includes everything you need to know about the NN-C777! I would buy this again.
;
Very satisfied! I was searching for several days, but nope; till I discovered your webside and there it was at a very reasonable price. Keep up the good work!
Paul
Flanders
 ;
Generally speaking good copy; a few pages too hard contrast...
Good service and communication.
;
I purchased the unit from a private party and the original owners manual was not available. Having the ability to download it was extremely helpful and clarified operating the equipment immensely. This is a complicated unit and without the manual I would not have been able to maximize it's potential. Thank you.
Precaution
This equipment is intended for indoor use only. Do not use it outdoors or at places that are exposed to rain or moisture. Do not attach devices other than TK-C625U/E, TK-C655E, TKC676E, TK-C205(A)U/E, TK-C205VP(A)U/E, VN-C625U and VN-C655U to this mount/bracket. Install this mount/bracket horizontally. Do not tilt it during use. Do not install or use the unit in the following places. � In a place exposed to rain or moisture. � In a temperature outsside the operating temperature range (�10�C to 50�C (14�F to 122�F)). � In a place where corrosive gasses are generated. � In a place subject to vibration. When attaching VN-C625U, VN-C655U to this mount/bracket, please refer to the "INSTRUCTIONS" section of VN-C625U, VNC655U for procedures to install the converter unit. Please refer to the "INSTRUCTIONS" section of the camera in use for procedures to attach the camera.
Installing the Converter Unit
When using VN-C625U or VN-C655U, attach using the clamping bracket inside the top cover of the converter unit (supplied with the camera). Converter Unit
Clamping Bracket Top cover
Installation Procedures
WB-S621U Pendant Mount
1. Make a hole in the ceiling.
When a hole is not made in the ceiling
Groove Reinforcement Angle To route cables through the ceiling, make a hole of in the ceiling. 30 mm ( 1 1/4)
2.
Safety cable
2. Route the safety cable and other cables
Route the safety cable and cables that is attached to the reinforcement angle through the pendant mount. When a hole is not made in the ceiling, route the cables through the groove of the pendant Mount.
1.
Cable
Cables
3. Mount the Pendant Mount to the Ceiling.
Attach the pendant mount to the ceiling using 4 or bolts (M5 - M6).
4. Fall prevention
Safety cable Mount Hole ( 4.5 mm)
CAUTION
3.
The camera may drop or images on the screen may appear shaky if the ceiling material is not strong enough. In this case, reinforce using a reinforcement materials.
4. Connect the safety cable.
Bolt (M4) Nut (M4) Upon removing the camera mounting plate, attach the safety cable (not supplied) to the safety cable mount hole ( 4.5 mm ( 1/8")) at the interior of the top cover using the M4 Bolt (not supplied) and M4 Nut (not supplied). When attaching the camera mounting plate, ensure that the Front FRONT Mark mark on the camera mounting plate is facing a direction opposite to the Rear mark on the top cover.
CAUTION
Pay particular caution to the length, strength, pull and material of the safety cable in use to prevent the plate from falling.
5. Install the ceiling panel assembly (for attaching TK-C625U/E and VN-C625U)
Ceiling Panel Assembly Positioning Hole To install, align the protruding part of the ceiling panel assembly with the ceiling panel assembly positioning hole near the Front mark of the camera mounting plate. Ensure to tighten the screws (3 locations) assembled to the ceiling panel assembly.
NOTE
The screws are assembled to the ceiling panel assembly in such a way that they will not come off.
Rear Mark
Top cover
6. Connect the Cables.
Camera Mounting Plate Ceiling Panel Assy (for attaching TK-C625U/E and VN-C625U) Screws (3 locations) Connect cables to the camera. For details, please refer to "INSTRUCTIONS" section of the camera in use.
7. Attach the camera's ceiling mount. (Not applicable
to TK-C205(A)U/E and TK-C205VP(A)U/E)
Attach the camera's ceiling mount to the camera mounting plate using the 4 screws (M4 x 20 mm) supplied with the pendant mount. Ensure that the FRONT mark on the camera mounting plate aligns with the Front mark on the ceiling mount.
5.
Protruding Part
|
|
|
> |
|
