There are currently no product reviews.
Clear and easy to read. All details as expected. Price acceptable , and quick delivery.
Quick response and exactly what I was looking for and at a great fair price!
5 star quality on these downloadable manuals. Easy to read and all the information is there. A must when doing a custom install or needing to service your precious old school electronics.
So usefull to make my installation a breeze. 5 stars on quality.
very helpful, the information in these manuels are very detailed
NOTES: â¢ If you have selected âNOâ for the surround back speaker (see page 24), you cannot select this setting. 6.1-channel and 5.1-channel software is played back in the same way as âOFFâ is selected for above setting. â¢ When the sound is not output from the surround back speaker even though playing back Dolby Digital EX software (bearing the mark ) setting âEX/ESâ to âAUTO,â select âONâ instead of âAUTO.â
Select one of the following settings: 80Hz 100Hz 120Hz 150Hz :Select when the cone speaker unit built in the speaker is about 12 cm. :Select when the cone speaker unit built in the speaker is about 10 cm. :Select when the cone speaker unit built in the speaker is about 8 cm. :Select when the cone speaker unit built in the speaker is about 6 cm. :Select when the cone speaker unit built in the speaker is less than 5 cm.
Setting the speaker distance
âFRNT D (front speaker distance), CNTR D (center speaker distance), SURR D (surround speaker distance), BACK D (surround back speaker distance)
The distance from your listening point to the speakers is another important element to obtain the best possible sound from the Surround and DSP modes. You need to set the distance from your listening point to the speakers. By referring to the speaker distance setting, this system automatically sets the delay time of the sound through each speaker so that sounds through all the speakers can reach you at the same time. Set the distance from the listening point to each speaker with the range of 0.3 m to 9.0 m (in 0.3 m intervals).
NOTE: If you have selected âNOâ for âBACK SPâ (see page 24), you cannot set the speaker distance for the surround back speaker.
CAUTION: When using the supplied speakers, select â200Hz.â
NOTE: Crossover frequency is not valid for the HEADPHONE mode.
Setting the phase of subwoofer
Subwoofer phase is closely related with the distance from the listening position to the front speakers and subwoofer. You can change the phase to obtain better bass sound. Select one of the following settings: NORMAL :Normally select this. :Select when you feel the bass sound is better with this mode rather than with âNORMAL.â
C L R
Subwoofer 3.3 m 3.0 m 2.7 m 2.4 m 2.1 m
Setting the video output for DVD playbackâM.OUT (monitor out)
After connecting your TV (see page 7), select the video output jack type you watch the DVD playback. Setting this properly, you can use AV COMPU LINK remote control system.âThe TV automatically changes the video input mode to the appropriate position (see âAV COMPU LINK remote control systemâ on pages 60 and 61). â¢ âVIDEOâ is initial setting. Select one of the following settings: VIDEO S :Select when you watch the DVD playback through the VIDEO jack. :Select when you watch the DVD playback through the S-VIDEO jack.
Ex.: In the above case, set the speaker distance as follows: FRNT D : 3.0 m CNTR D : 3.0 m SURR D : 2.7 m BACK D : 2.4 m
Setting the crossover frequencyâCROSS
Small speakers cannot reproduce the bass sounds efficiently. If you use a small speaker in any position, this system automatically reallocates the bass sound elements assigned to the small speaker to the large speakers. To use this function properly, set the crossover frequency level according to the size of the small speaker connected. â¢ If you have selected âLARGEâ for all speakers, this function does not take effect and you cannot change the frequency.
COMPNT:Select when you watch the DVD playback through the COMPONENT VIDEO OUT jacks.